Crusader103 Posted February 3, 2019 Share Posted February 3, 2019 Hi All, I've got about 12 years experience designing homes but I'm new(er) to Chief Architect (Premier X10). I've found a lot of help on this forum (thanks) but running into an issue here. I need my roof to look like the attached image. So far, it's not close. Specifically, I need the roof on the left side of that gable above the door to die into the garage roof. I also need the right side of that same gable to meet the lower floor roof. Essentially, I'm looking to recreate the picture. I've attached my plan (very much in progress). I've got a lot left to do on this plan and know how to do most of it. I just want to get past this one sticking point before I get too far into it. Any guidance is appreciated. 2-Story 4 Bedroom.plan Link to comment Share on other sites More sharing options...
Alaskan_Son Posted February 3, 2019 Share Posted February 3, 2019 Is there something in the water? It seems like we’re seeing examples of people using those gable into gable drainage hazards about once a week this days. 1 Link to comment Share on other sites More sharing options...
Doug_N Posted February 3, 2019 Share Posted February 3, 2019 Yea, but then think of all the great work for roofers down the road Michael. Link to comment Share on other sites More sharing options...
GeneDavis Posted February 3, 2019 Share Posted February 3, 2019 I don't see the problem, and the house looks pretty much like everything built in the last fifteen years in the part of far northwest Chicagoland with which I've some familiarity. Gables galore facing the street. That previous one was a roof seriously in need of a cricket, but not this one. Link to comment Share on other sites More sharing options...
Chrisb222 Posted February 3, 2019 Share Posted February 3, 2019 Solver's roof would drain well but I haven't seen that exact design. Usually there's a ridge at a right angle to the front gables, in which case a cricket would possibly be needed. All depends on where the hip coming down from the perpendicular ridge meets the gable planes. Link to comment Share on other sites More sharing options...
DRAWZILLA Posted February 3, 2019 Share Posted February 3, 2019 with all the building height limitations here sometimes you have no choice but to use double gables with crickets. Link to comment Share on other sites More sharing options...
Jay_on_Cape Posted February 3, 2019 Share Posted February 3, 2019 15 hours ago, Alaskan_Son said: Is there something in the water? It seems like we’re seeing examples of people using those gable into gable drainage hazards about once a week this days. I draw my own plans but if I just was a builder and didn't draft them and a designer came to me with one of those water / snow traps I'd fire them. You see a ton of them in GA. If I had a penny for every garage I've seen down there with a gable across the entire face of the garage that dies into the gable wall of a house...... Link to comment Share on other sites More sharing options...
Crusader103 Posted February 4, 2019 Author Share Posted February 4, 2019 Thanks for the info to all. If I am reading you all correctly the only way to do this is with the manual roofs. I agree, based upon the image I am trying to copy, that drainage is an issue. I'm not trying to design this house so much as I am trying to figure out how to do certain things with X10. I like CA so far but I'm also trying to learn how to make some things work in it. While I try to avoid issues in my plan, most of you probably understand that in the end the individual client or builder gets what they want (pay for) even if I point out to them some faults in the design process. Yes, it's my job to point it out to them. But when I do and they want it anyway, I let them know there is going to be a problem and then deposit the check. Link to comment Share on other sites More sharing options...
glennw Posted February 4, 2019 Share Posted February 4, 2019 19 minutes ago, Crusader103 said: If I am reading you all correctly the only way to do this is with the manual roofs. No, not at all - this should all be able to be done with auto roofs. I managed to get the front roofs all auto built, but couldn't go any further because I don't know what types of roofs you want at the rear, and what ceiling/floor heights you want: Eric, I am curious - would you really build a roof like that? Link to comment Share on other sites More sharing options...
Crusader103 Posted February 4, 2019 Author Share Posted February 4, 2019 9 minutes ago, glennw said: No, not at all - this should all be able to be done with auto roofs. I managed to get the front roofs all auto built, but couldn't go any further because I don't know what types of roofs you want at the rear, and what ceiling/floor heights you want: 9' main floor, 8' upper floor. And honestly I didn't have a plan for the rear. I was just trying to figure out how to make the front look like the picture. Just getting that center gable to terminate into the roof of the garage on the left was my issue while getting that same gable roofline on the right to meet the roof coming from the main floor below. I'm not designing this house for anyone. I just want to know how to do it. I can do it on paper and in non-CA programs. I'm just trying to build my knowledge of X10 is all. Link to comment Share on other sites More sharing options...
glennw Posted February 4, 2019 Share Posted February 4, 2019 Eric, I redid the roof correctly this time (still auto roofs) with the center ridge lower and not being a continuation of the left hand roof. And guess what - I get exactly same roof as you. Certainly not a roof that I would ever build! Yours: Mine: Link to comment Share on other sites More sharing options...
HamlinBC Posted February 4, 2019 Share Posted February 4, 2019 We don't design cricket to a point. Leave 8" to 10" fascia at bottom. sample 2.pdf Link to comment Share on other sites More sharing options...
Ridge_Runner Posted February 4, 2019 Share Posted February 4, 2019 53 minutes ago, HamlinBC said: Leave 8" to 10" fascia at bottom. Interesting way to do it. I will have to keep that in mind. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now