robdyck

Members
  • Posts

    5052
  • Joined

  • Last visited

Everything posted by robdyck

  1. I have also noticed that all concrete objects now fill using Chief's embedded concrete fill pattern. My settings are ignored for concrete walls and floor structures. For basements I had control over the wall and floor, but never the footing fill. For me, this is not a problem because I always replaced Chief's fill pattern for the footing with my own, which was my same choice for concrete walls and slabs. I have that fill pattern in my library with a tool linked to it. When I use the spray fill tool, I just ensure it is in Floor mode and then it replaces all matching fills at one time.
  2. Hey there! Let's assume for the moment that it's a bit of a nuisance to create a millwork symbol for a 2x4. You could use a normal interior wall and edit the wall framing. A few suggestions: Open the wall dialog(Structure tab) and check 'retain wall framing'. You can still edit the framing, but it won't automatically rebuild. Open the wall detail and edit the framing. Also, move all the studs to the Walls, Railing layer or a copy of that layer. In plan view, make the wall invisible after the framing is locked. If you make a custom wall type before doing this, that should allow you to preset the stud spacing and the top plate count.
  3. YES!!! For me the lag comes with typing text and navigating dialog boxes. A couple of hours max before a restart is required. It is TERRIBLE Everything with the model and rendering is pretty much as fast as I'd want it.
  4. Rich text boxes will occasionally do that even if auto height is checked. IF auto height is checked, a click-close or a nudged left-right should cause it to correct itself.
  5. That's a very good question! The typed value will be applied although the value displayed will appear as a rounded fraction. You should be able to test by typing in the various values and seeing the effect in the preview. However, when I'm making adjustments to small values (like in a layout file) I will press the 'Number Style' button at the bottom left and switch to decimal inches.
  6. The previous 2 responses are correct. When the callout is 0.35" or smaller, that problem is triggered. It must be 0.36" or larger (according to my testing).
  7. There's no default setting that will omit the end stud. I'd let auto framing do it's thing until you get to a stage that some manual framing cleanup won't have to be continuously redone. And, if the walls are finalized, you can leave auto-framing on for the roof so that you can edit wall framing while still adjusting the roof and roof framing defaults.
  8. @Matt_S Great! If you wanted to, you can also add leading / trailing zeroes to that marker. You can do this in defaults, or just double-click and adjust there.
  9. @Matt_S To notify someone, type the username with the @symbols first. In the Plan Defaults, try changing the 'zero' to -11 1/2". Windows Snipping Tool has some basic markup tools at the top of the view after you take a screenshot.
  10. There may be a bug relating to some types of decks. I encountered something similar this weekend on a project that hasn't had that problem before. 2 decks, one on the front, one in the back. Auto-building only worked on one of them after this most recent update. Exact same room definitions. I haven't reported it and I could be wrong about the cause.
  11. In plan view on the Attic level, All you need to do there is grab the corner handle of the adjacent wall and drag a perpendicular section to connect them. Select the new wall and use the align tool to make sure it aligns with the wall below.
  12. Hi Jonathan! Try changing the railing wall type around the Carport (Floor 1) to Siding-4 (this will address the attic wall).
  13. Yes, the ceiling planes, right? What I was suggesting didn't have anything to do with auto framing, only the problem Gene indicated which was the wall top. I locked all the framing before connecting the roof valleys. In any event, it was the roof that forced the wall down as roof trusses will not cause an effect on the wall structure geometry. It's fairly common to have to edit trusses and the truss bottom chord could be edited to cleanly bear on the top plate.
  14. I'm assuming he is referring to the wall shown in his image. When I join the roofs at the valleys, this wall top is correct.
  15. This is simply because you're relying on the roof plane to also provide the sloped ceiling plane. For more and improved control you will need to use ceiling planes independent of the roof planes. This will allow you to properly model ceiling planes and allow you to join roof planes at their valleys.
  16. Impressive stuff! Questions: Does it matter which AI tool is used (is one better than another)? Can the AI training be shared? For example could you share (sell) your trained agent? Would a pre-trained agent be able to work across different plan templates? For example, trained on your template but operate reasonably well on my template.
  17. AFAIK, notching is not possible. You can attempt to bury a portion of stairs in a wall but this will be painful. You can break the stair at the full tread before the notch and then add a 3d solid.
  18. This may be close enough: K-3203 Brockway Wash Sink You could add the drain boards manually to that symbol if you really needed to.
  19. You can add that railing right from the landing, but the handrails will probably not connect.
  20. I'll show some screenshots from a simple example. Plan View: On the 2nd floor, the roof baseline has been set at 109.125 + 16.875. Section: Attic rooms have a 3.5" floor structure & no floor sheathing. Bonus Rm has sheathing over 2x10 joists. I've manually added the sloped ceiling planes. Build roof trusses. Manually adjust the truss profile where needed. In the truss detail, manually add the 2x10 bottom chord.
  21. I'd suggest using a wall (no room definition) with a wall cap. Use CAD lines and arcs to create exact geometry for reference and snapping. Work on one side of the stairs only and copy/reflect about the center when complete. Draw the wall at an angle. In section view, manually lower the top of the wall to be parallel with the rise angle. Then, in plan view, curve the wall and set it's radius to match your CAD reference arc. Use the point-to-point move tool to align the arc centers. For the stairs, first add and shape the flare and I'd also make sure winders is checked.
  22. I'm not sure that Chief has ever had that function, but it sounds like it would be a good option to add next to the Open View function. For CAD details, you could consider placing each detail in its own CAD Detail view. This can help you organize and use the details with specific naming, scaling, and view cropping and centering in layout.
  23. If it affects the model, then in one form or another we could assume it's still there. Did you accidentally place it on an non-displayed layer instead of deleting the wall? If you can post the plan file, I could take a look and let you know what I find.