Kbird1

Confirmed here : The Problems I am having are not new to the new update as far as I have experienced. I am not sure what Chief is doing with the C++ ADF though and I intermittently see the Crashpad Handler as in above Pic.

Put a copy back in the HotKeys Folder ( or copy over from X12 Hotkeys Folder if need )

Just got my 1st lockup for today closed an elevation , said yes to update Layout , then reopened Elevation to check I'd done something almost immediately, looked good, so I closed it again and it has hung........ still hung after typing this so will need to force close I think.......

A few have had toolbars issues , try going to Preferences>Reset Options> Reset Toolbars

No Crashes yet , but the black screening (2-3 secs) in the Elevation Views and sending to Layout is still happening as it did in the previous Version. Currently using Nvidia's 471.96 Drivers ( latest AFAIK) on my 3080 M.

As Eric mentioned a plan would be handy otherwise we are playing 20 questions..... 1.) make sure all Roof plane pitches are identical 2.) makes sure the Roof plane Baselines are where they should be ...ie over the main layer of their respective Wall. M.

There won't be any updates for X12 now X13 has been released ...... X13 maybe in you Locker though if your SSA was/is Valid

This is the Help article for Home Designer Users which may help explain what Glen say a bit more for you https://www.homedesignersoftware.com/support/article/KB-00358/automatically-building-a-one-and-a-half-story-roof.html Home Designer Forum : https://hometalk.chiefarchitect.com/

It sounds like you are using Home Designer Arch. 2021 not Chief Architect Premier , so it would be best to ask questions over on the HomeTalk Forums (Blue Theme) as the libraries are Different in the Home Designer Series of Products. https://hometalk.chiefarchitect.com/

You cannot have defaults for the 2nd Floor pre-setup, ( disregarding the SAM Method) but are given the chance to change and set them up in the DBX when you create the second floor , if you just click OK ? Chief copies the Defaults from the Floor below.... M.

Have you perhaps toggled Perspective Crop Mode On? is it hotkey assigned maybe? it is no longer on the Toolbars by default but can be placed there manually.

No..... same issue as above when I tried it OSB will go flush with -7/16 but Sill plate remains in line with outside edge of foundation wall. Maybe I missed something though? * If you make the sill plate wider by 7/16 ( 7 13/16) , in Cross Section you can click on the end of it and pull the edge back in though to 7 1/4".

That would buy you a Nice high End PC and give you everything you need, but you'd have to comeback to the "Darkside" It really depends if you "need" the new RTRT Views in X13 (for PCs only) or you are fine with a X12 like experience, and can wait for a year (or two?) till Chief finishes the Metal API for the new Astral Lighting Engine, so macs can use the new Camera Views. There was some new Mac News about upcoming Releases earlier today but not to much on MAC GPUs except to say the M1X maybe as fast as a GTX1650 in the new MacBook Pros. M.

PBR can cause the GPU to continue to run if Live Samples are not capped , I don't think TI has that Issue , of course if you are rotating the view etc it will need to be updated. does Vector View have the same issue? People would likely need your plan to test with I doubt the update will help it is pretty small by the look of it and mainly for mac users.

you aren't accidently using PBR instead of a STD or Vector View are you? there was a small update to X13 today you could try too... M.

I agree of course, and I guess do that without thinking, but I would just use a Cross Box in CS if I needed to show a wider sill plate since it is about the only time you will see a Sill Plate. M.

I believe you are right , and I think I used to just use a CAD Box over the Sheathing layer in C/S's back when we could have 2x4 ext. walls, same as I extend the Auto-Detail box for the Siding down 1 1/2" as well since Chief can't do it auto. M.

Good catch Steve , I never noticed the Wall above was 2x4 as we have to use 2x6 locally. I would call this a bug myself the mudsill should always be flush to the outside of the foundation wall, no matter it's width. I can see now why Adam doesn't want to have to rebuild his Walls for a new Template ....that is a lot of walls...... but with the Changes to Framing in X13 they will need to be updated so the Main Layer is set as a Framing Layer, as you showed. M.

Thanks for the Update............ chief-architect-x13-update-notes_2.1.3.pdf

Did you rebuild the foundation? Here is a X13 test plan with the right side using the FDN to OSB layer and the Left Side using the -7/16 method. OSB Flush to FDN.plan

sounds like you tried changing it in the Roof Build defaults? and should of used Edit All Roof Planes ( as the Roof planes already exist in the plan) If you change the Soffit material to T&G in the Roof build DBX in your template plan used for all new projects it will be T&G on every job.

You may have to show the angle you are talking about, most of my examples were to help Mark's situation, but I thought most were less than 180°? .............inside corners are definitely more finicky but are do-able....

Not that I am aware of but you can add a Custom Icon to the toolbars with the Place Library Object Tool and assign the double headed arrow to it... more info here : https://www.chiefarchitect.com/support/article/KB-00811/customizing-toolbars.html

It is that the Room has a Height reference , not that it has Room Definition that causes the wrap to work as I showed above.... The two stairs are not identical so they won't wrap till they are, I usually copy the 1st one I draw to make sure they are.... There is something else up in this plan though.....

the -7/16 in your OP works for me in a X13 OOB Template Plan , so I am not sure what is up with your current Template... test it for yourself perhaps.... *** I should of mentioned that like Ryan below that method works for me too...