robdyck

@Alaskan_Son Great Explanation!

That's never been an issue, I think they just improvise.

I always specify the installation methods and fasteners for shadows to avoid that problem.

Open the distributed polyline, then edit the current object and set its elevation reference to be absolute. It would be simpler to just have your mulch as a terrain feature and leave all the plants following the terrain...

Another thing to remember when using a CAD detail (or any drawing for that matter) is that you can and should adjust your page size to match the drawing scale you'll be using. This will be helpful for a few things: seeing how much space the detail will take up on the printed sheet planning the location of the detail on the printed sheet seeing the Print Preview accurately in your detail window the detail will then be sent to layout at the correct scale line weights will not need to be different across layer sets allowing you to Modify All Layer Sets when its necessary or desirable to do so Example of a detail with the default 1/4" scale page setting After adjusting the page size It might not be that obvious from the screen captures, but the 2nd image prints much better and all the text, dimension arrows, line weights end up exactly the same as the 1/4" scale section views...unless you choose different settings of course.

Open the room dbx, floor finish, check default.

Sent you an email.

Then click default.

That's because you have a room on the 2nd floor over those rooms. Get rid of a wall so there is not a room over the kitchen or living room.

Those rooms have the floor finish layer defined as a 0" thickness. Make it 7/8" like the other rooms...or the default thickness, or whatever you'd like.

Click on the baseboard.

First to accept the credit and subsequent gratitude goes to me though!

For a situation like that, I use a cabinet that is 4.5" deep (to keep my toekick). Keep in mind that an actual cabinet will probably not be mitered to a sharp 45. Rather, the face will be slightly away from the wall and a filler strip would be used...either ripped to 45 into the wall or placed perpendicular to the wall and mitered to the cabinet face. Then, I'd use a polyline to clean up the display in plan view, and a custom countertop.

@ChiefuserMathews It does look like a hand rail bracket mounted near the top of the concrete wall might be a bit far from the upper end of the hand rail. The last thing you'd want is an installer fretting about that, then mounting it too close to the top and blowing the concrete out. That was the reason that, in an earlier post, I mentioned aligning the inside of the concrete wall with the exterior of the deck framing (although I wasn't overly specific)

Highlands_Lot6.3_2.plan

Problem #1: the roofs aren't connected at the top. Problem #2: this wall isn't long enough. Problem #3: this wall doesn't align with the floor below Problem #4: the hole in the lower roof plane isn't the right size. Drag it up to the exterior of the wall. Problem #5: some walls aren't using the default top and bottom height. Recheck those. Clean up the other side to match. Notice the side wall is broken into 2 segments:

Hey Darren, glad you got it figured out. A few quick additional items will help with realism, although you may be ahead of me and have already done it. In elevation view draw a polyline 3/8" larger than your arched lintel course. You can replicate this for: material region to remove the brick polyline solid to be the mortar for the arched lintel.

Hey Wilson, to initiate a reply from another user of the forum, you need to either quote them or tag them. That will send out a notification. @ChiefuserMathews

Did you build the terrain on the main floor? That's where it belongs. I bet you built it on floor 0 so you'll need to follow Dermot's advice below.

Or the deck....or both.

You've got to click the handrail molding.

Your point is in the wrong spot. It needs to be the center of your arch so the solider course is concentric.

What I mean is that by using a schedule with the custom field for seating, the data will at least be correct and live. The resulting schedule can be copied into a spreadsheet for totals and any other editing.

From Help: Display Options - • Uncheck Display Column Headings to hide the selected schedule’s Heading row. When this is checked, each column has a heading at the top. • Uncheck Display Totals Row to suppress the bottom row stating the total area for all objects in the selected schedule. Only available in schedules set to include Door, Window, or Room categories, and only when one or more “Area” columns are included.