GeneDavis

That worked for both base and wall adjacent a tall. I cannot seem to succeed doing a filler between the wallcab and the fridge box, which is built with a tall partition each side and an 18" deep wallcab on top, the wallcab moved out to the face of the 25" deep partitions. https://www.dropbox.com/s/653dfr744uu7dii/Fawn Ridge Downsized.plan?dl=0

Shouldn't I be getting one here? The space is 1.5"

We can do it for walls by putting them on a layer and unchecking the M. Chief looks at the wall as an assembly of layers, and when then running the material list, does not include the materials for siding, sheathing, drywall, or insulation. But we've no similar way to do this for roof planes. How do you make it such that a roof plane's materials are not tallied in the material list? One can put the roof's polyline (what you get when selecting a roof plane) on a layer and specify that layer without the M checked, but that does not do it as it works for walls.

This is helpful, Glenn. I will edit my model so as to try this out. How do room finishes and structure come into play in this? My model, attached here, has a simple house part, which is entirely as-built, and a room addition which is to build atop existing deck framing, plus an all-new screened porch under roof, to replace the as-built smaller one there now. It is all (the new room and porch) at level 1, and I have not built a level 0 (which there is, as this is a walkout lower hillside house) because the log columns are all to be re-used in the new. My purpose in all this is not so much to produce any construction docs, but to do a framing workout and produce a material list. One of the mysteries is the deck under the porch roof. It is built, planking and framing, and appears on level 1, but will only come through in materials when the all-project list is generated, and then the deck planking and framing is listed as on level 2. What is that about? McMillen Whitney.plan

How is the best way to get the material list to capture only the new work part of a job? I have modeled enough of the house to do the porch and room addition, and have a mix of as-built floors, roof planes, walls, decks, etc. on the plan. I see the "exclude from schedule" checkbox, but I don't think that is going to do it.

I use Chief to do the layout and for doing renderings, but rely on the free software eCabinets to build and source components. Ecabs lets you build a "seed" for every cabinet type you can imagine, and then for an installation, one simply inputs the variable (almost always just the width) to produce everything needed for the job. The hardware lists are generated also, and are all based on your preferences. For the example of basecabs with drawer stacks, I have seeds built for kitchen-height 3-drawer stacks with the drawers all equal height, and for the drawers as a small height top and two equals under, and similarly for a 4-stack. Same for "bathroom height." Whether you build faceframed or frameless, you build your seeds accordingly. And every element of the joinery is specified the exact way you build. If CNC-cutting for blind dado joinery, you can specify and set dado size, depth, mortise width clearance, depth clearance, everything. In eCabs I can input the data for a whole house job of cabinetry, using the Chief generated cabinet schedule, and produce the complete cut list for carcase parts, all the purchased (or built) doors, drawerfronts, moldings, drawer slides, hinges, susans, and other goodies, in short order.

Thanks for those, Cheryl. I have snips from Game of Thrones, Warren Miller extreme skiing, and NFL closeup action. I just thought that it is such a common need that a Chief bonus library would have something. Is there a bonus library for entertainment furniture and fixtures? TVs, TV tables, credenzas, stands? Speakers? I looked, but maybe not carefully enough. The ceiling-mounted speakers, both flush and mounted. The subwoofers. Sound bars, Center-field speakers. Stacks. All that stuff. Media room gear. Where is it? Should we have it? Has anybody asked Chief?

Where are these in the libraries? I have been looking and striking out. Everybody wants a 75 inch TV on the wall or standing on a wide console, so how is it best done and where are the images of golfing, basketball games, football games, shark week, whatever? I have done it before building a solid with surround frame, snipping images from the web for the screen, but doesn't Chief have these in some library somewhere?

I disagree. It's fascia, the finish, that you want to match, and I am glad it is there. If Chief did not give us the ability to lock fascia and rotate from that point by setting either pitch, or one of the other elevation points (baseline or ridge), we would have to work harder to do the match we need when dealing with roof configs with differing pitches. You just have to realize, when doing the lock on fascia, how it will affect, say, baseline, if you change pitch or ridge.

Happy Easter, everyone! I have been having a dialog with the truss designer for the project plan attached here. A cross-gabled roof has two side bays of slightly lower pitch intersecting a center bay, the center bay's ridge just 2-1/4" higher. Fascia heights are to match, and the fascia boards are 1x8s. 3/4 x 7 1/4 to be precise. I gave Mr Truss Guy the heel heights, pitches, and overhangs I derived from the Chief model I made, and I used all the Chief roof spec tools to get a model in which the fascia heights match exactly. I did not give him the fascia height. He built his truss model using his software, and came back saying the fascia heights did not match, and to study things, I used Chief CAD to see what's happening. Well, here seems to be the problem. Listen carefully, as there is some detail here. I always thought the Chief roof plane dialog, showing us the numbers for heights at ridge, baseline, and fascia, that the dialog is returning us points in 3D space that are co-linear. We all know about how a roof plane is manipulated with Chief, using the lock function. You lock fascia height, and that becomes the pivot as you change one of the other variables, either pitch, baseline height, or ridge height. Or you lock pitch, and change one of the other variables, either facia height, baseline height, or ridge height. Whatever your preference, the roof plane is rotating as you change a variable. And I always presumed all those height points were co-linear. And it was with that thought that I used CAD to see what Mr Truss Guy was saying. I drew the two cross sections of my building in CAD, and using the roof overhang distance, fascia height, and ridge height, the two heights right from the Chief model, sought to proof the heel heights. And that is when I saw the bust. When Chief generates the fascia and places it in 3D space, it is using the roof sheathing spec for thickness, and the fascia spec for thickness, to place the fascia so its outer top edge is co-linear with the top surface of roof sheathing. Chief is returning the true fascia height when it shows the figures in the roof plane DBX, and the thicker the sheathing, and the thicker the fascia, the more not-co-linear that fascia tip becomes, relative to the roof plane line. Mr Truss Guy did not tell me what fascia height his software generated with my specs, but now that I understand what Chief is doing, I'm going back to him and specifying only heel height and ridge height for the two roofs, and explaining that with my thicknesses of sheathing (5/8") and fascia (3/4") and logic that roof overhang is to outside face of fascia, he can be assured that we will have the common fascia height we need. Fawn_Ridge_Downsized.plan

I'm in FL but my jobs are in a place in NY with a 90 psf ground snow load. With a 27 inch gable roof overhang, we'll do upright 2x6 lookouts.

Thanks, Chopsaw.

I suppose I can draw a p'line solid, call it framing, and get it done that way, but I think it's a void in Chief that ought to be fixed. I'll do a suggestion. Edit: No, while a single p'line solid precisely drawn in 3D space will "work," in that it will be seen in a 3D framing view, because it is not a roof framing member, it cannot be copied and placed elsewhere in that roof plane, or another plane, and behave as a true roof framing member will. So, I was able to get another roof plane in my plan, one with the same pitch as the problem one, to generate a lookout, and that is all I need to be able to copy and mirror and whatever, to get them everywhere needed. But I still want the ability to "draw" one in place.

Solved, sort of. Unchecked the "retain" thing for a single selected plane, checked "build framing" and it gave me the subfascia, the ridge, and an unwanted rafter. But no lookouts. I started another thread about the lookouts.

Can this be done? I'm stuck. Roof is trussed, which of course must be done manually. I unchecked "retain roof framing" and built framing but Chief failed to autobuild lookouts. The only framing tool I can see to use is the one for drawing rafters, and it places lookouts oriented plumb, when everyone knows lookouts are rotated to match pitch.

This is what it says in Help and yes I have this box checked. "One checkbox is unique to the Structure panel of the Roof Plane Specification dialog: check Retain Roof Framing to keep the selected roof plane’s framing from being deleted and replaced when roof framing is rebuilt."

Yes, retain roof framing is on. I thought that is right for this situation so that the BUILD does not compromise anything I already placed.

I framed the roof with a combination of trusses and sticks, and now want to build roof framing in order to get ridge fills, subfascia, lookouts, etc. Must have set something to block it because when I do the build framing command, nothing happens. Fawn_Ridge_Downsized.plan

Do my little three-roof-plane test. Work with Chief as it is and select all three and edit what you can. Try everything, because you do have editing capabilites. How you edit opens up other fields for edit. Go back and do it differently. Observe results. Now tell us how you want it to work that is different. Be specific. The roof planes in this test are like three postage stamps, three different sizes, all pitched, in 3D space. Chief gives us control of their pitch by letting us fix either the ridge, the baseline, or the fascia top as the pivot, and then having fixed that, change the pitch. Chief also gives us control of the plane by us specifying the z-height (elevation) of any two of the pivot lines (ridge, baseline, fascia top), in which case Chief computes and returns the pitch stated in x/12 or degrees. Chief's editing, when we group select or multi-select roof planes, is consistent with what we see presently, because we get all the possible editing capability we can have for COMMON edits of planes which are dissimilar in various ways. Solver showed clearly how differently it works when selecting two planes with common runs, versus selecting planes with differing runs. But hey, maybe I am wrong and not seeing what you see. Show me. Be specific.

Do a little test. It's quick and easy. Draw a new rectangular floor plan, divide it into three by drawing two interior walls, then set each room at different heights. They are all set to default at first, so just change two. Now manually draw a little roof plane over an outside wall of each room. Make sure the run of each is different. Change two of the three to have differing pitches from default. Now you have three absolutely different roof planes, Each has a unique pitch, a unique run (the 2D length from baseline to ridge), unique fascia heights, and since we are in 12, we are looking at the shadowboard top height also. In this test, since we've not placed shadowboards, that field is blank. OK, select all three, and study the DBX and how things work. Tell us how you want Chief to work for you, different from how it works now.

It is logical to me why you can’t get full edit control of multiple roofs in some circumstances. Every roof has a RUN. In plan view you DRAW it by the drag after the baseline drag. The DBX dialog gives us the ability to edit either VERTICAL POSITION of the plane (by locking pitch) or its ROTATION & VERTICAL POSITION. But no DBX edit of run is permitted. Look at it. Nothing you do in the DBX changes the plan view of the roof you are editing. So it is perfectly understandable why the only roofs you can multiple select and have full height and rotational editing control for are those with everything equal including RUN. And that is the way it should be.

Where is the code reference found in NY Residential (or IBC) that stipulates this? All I can find is that the gathering floor is to be sloped.

Hint: complete your signature line in your profile (it's easy) so we can see what software you are using and what your system is about. And try the search function. There have been lots of threads about this.

Do the math and you can see that an 8" stemwall with a 2x4 framing wall, no sheetrock on stemwall side, spaced 1/2" away from the 'crete face, yields a 12" dimension outside stemwall to inside framing wall. With the wall positioned as I want, with the 1/2" gap, the window won't behave. Only when I open the gap by another inch, to 1-1/2 away from the stemwall, will the window behave. I wonder if a room divider wall in that space somewhere, maybe 1/4" inside the stemwall, will change things.

In the pic shown here of the plan view, there is a doubled wall, a 2x4 framed wall with drywall only on inside face, spaced 1/2" from face of the 8" stemwall, and maybe that is causing the problem.