RobUSMC

Ive seem to always have issues with bow window editing. I place the bow into the wall then in camera view select the unit then adjust the width, depth and how many windows make up the bow. I can never get the windows to size correctly or to connect without any framing between the windows. I have "No Framing Between Components" checked. When I tab to select a single window, I can adjust the window type,casings, heights, etc. but the width will not change. The actual windows are 21" wide but the max width it will allow is 10". I even tried to change the framing defaults with no luck. It shouldn't be that hard to do as these types of single bow window units are common. Any ideas? thanks

Does anyone have symbols / textures or know of a good source for good seamless textures that doesn't need to be cropped and tweaked just to get a decent look in Raytrace. Thanks

Ive done it both ways for a work around but just wondered if there was another way. Thanks

I built a kitchen island with standard 24" deep cabinets on the front and I have butted 18" cabinets to the back of them to give me a 42" deep island without the eating area overhang. On the ends in both vector or elevation view you see the separation line between the back of the cabinets. I have both cabinet with a flat back with the toe kick and the countertop overhang. Again, it minor but I don't want my install crew to think there are two end panels butting together there to create a seam.

Perfect. Thanks alot

Has anyone seen or have a symbol for a countertop pop up outlet like ive attached? I checked 3D WH but didnt see anything Thanks

I 2nd, 3rd and 4th that recommendation !!!!!!!!!!!!!!!!!

Add Legrand Adorne to the list. We are using alot of this new switches, outlets and specialty trim. http://www.legrand.us/adorne.aspx

Great... Emser is also a good one with nice natural stone

Delta / Brizo Plumbing Updated Cambria Updated Cambria Vicostone Quartz countertops WilsonArt Arizona Tile Or another Tile MFG in addition to Dal-Tile DeWils Cabinetry

Thats were it is. Thanks

This is what i use. http://www.leica-geosystems.us/en/Laser-Distancemeter_5061.htm

I searched the forum and found the subject and someone said Chief had a curved bottom starter stair tread. Does anyone know where it is. I did a library search for tread, starter and starter tread and found nothing

Ok. same as doing a tile backsplash using PS

I saw the ones on 3d WH but they were were more the European style. Ive never tried to apply the pic to a PSolid then convert to symbol. will try to figure out how to do that. thanks

I normally would not design the seperate boxes but in this case these are switches were not touching and I like to get my rendering as close as possible to what they have. Any idea about the bounding box offset?

Yes. Thanks Dennis. That magazine rack was the selling point of the project

Just a hodge podge of stuff

Hopefully I can explain this clearly. This has been an issue for several versions as far back as I can remember. When placing switches on a wall and viewing them in camera view the switch and bounding box never line up with each other which makes it tricky to position them where i need them. I could see this with an imported symbol but these are core symbols. Also like in the attached photo, there are two separate 2 gang switch boxes and when I attempt to move them into the correct location and get 6-8" from each other they will snap together and create a single 4 gang box. The same thing happens with outlets and like the switches they will actually overlap and sit on top of each other. Is this a snap issue where they merge together? I wouldn't think a snap issue would not make the symbol and it's bounding box offset from each other. These are currently in X7 Thanks as always Rob

We have started using the Legrand line of switches/ outlets, etc. I've looked on 3D WH and found a few symbols for they are mostly for European countries. Has anyone ran acroos or made any of these symbols. Ive attached a few pics from their lineup. Also the website is http://www.legrand.us/adorne.aspx Thanks Rob

https://3dwarehouse.sketchup.com/model.html?id=u5a43da11-e7d1-453e-99a2-0f1e0c0c66f4 Shower Door Towel Bar.calibz Shower Door Towel Bar 2.calibz

See attached

C:\Windows\System32\cmd.exe /c "echo off | clip"

Are you saying you need this new addition to be raised approx 11" from its current position.

https://3dwarehouse.sketchup.com/search.html?q=stainless+sink&backendClass=entity