ACADuser Posted October 21, 2014 Share Posted October 21, 2014 How can I close the walls so no notch? Link to comment Share on other sites More sharing options...
Dennis_Gavin Posted October 21, 2014 Share Posted October 21, 2014 Spread the wall apart further. Take a dimension across the area. Click on the wall you want to move, select the dimension and set to zero. It should then snap tightly up against the other wall. I think. Link to comment Share on other sites More sharing options...
kMoquin Posted October 21, 2014 Share Posted October 21, 2014 Drag the wall with D07 edit handle down so it joins the other wall with the slider. Link to comment Share on other sites More sharing options...
ACADuser Posted October 21, 2014 Author Share Posted October 21, 2014 When you do that it creates a notch at the cabinet side of the junction. Link to comment Share on other sites More sharing options...
rlackore Posted October 21, 2014 Share Posted October 21, 2014 Break the south wall at the intersection with the west wall. Now redefine the little stub of the south wall to be 8" total thickness. Link to comment Share on other sites More sharing options...
kMoquin Posted October 21, 2014 Share Posted October 21, 2014 When you do that it creates a notch at the cabinet side of the junction. Seems to work for me. You may need to post the plan to get more than guesses. Link to comment Share on other sites More sharing options...
ACADuser Posted October 21, 2014 Author Share Posted October 21, 2014 Seems to work for me. You may need to post the plan to get more than guesses. Your walls are too far apart. The north south walls share the framing line. i.e. no drywall. Link to comment Share on other sites More sharing options...
Alaskan_Son Posted October 21, 2014 Share Posted October 21, 2014 Can you please just attach the plan? Link to comment Share on other sites More sharing options...
ACADuser Posted October 21, 2014 Author Share Posted October 21, 2014 Break the south wall at the intersection with the west wall. Now redefine the little stub of the south wall to be 8" total thickness. wall int.png Walls will not break but pulling then apart I made a short 8" thick wall out from the intersection & then moved it into place. Link to comment Share on other sites More sharing options...
kMoquin Posted October 21, 2014 Share Posted October 21, 2014 Your walls are too far apart. The north south walls share the framing line. i.e. no drywall. Then Robert's answer is the one you need. Break the south wall at the intersection with the west wall. Now redefine the little stub of the south wall to be 8" total thickness. wall int.png Link to comment Share on other sites More sharing options...
ACADuser Posted October 21, 2014 Author Share Posted October 21, 2014 Here is a test plan WallTest.plan Link to comment Share on other sites More sharing options...
rlackore Posted October 21, 2014 Share Posted October 21, 2014 Walls will not break but pulling then apart I made a short 8" thick wall out from the intersection & then moved it into place. The walls will break - you just have to keep picking points a bit farther away from the intersection until it happens. CA is funny that way. Link to comment Share on other sites More sharing options...
Alaskan_Son Posted October 21, 2014 Share Posted October 21, 2014 Structure tab of wall you want framed through...Double wall>Furred wall Then use the edit handle to extend the wall and it should work fine. P.S. Whenever possible, its good to attach the whole plan (at least as much as possible), there are often times other intricacies of the plan that may be affecting the problem, or that may be affected by the solution. Link to comment Share on other sites More sharing options...
Alaskan_Son Posted October 21, 2014 Share Posted October 21, 2014 Roberts solution may also work, and one other option that works decently well (but not great)... Checking Through Wall At Start/End for the walls (in the wall structure tab). This will likely leave one small section where one of the walls is butting into the drywall of another wall though. Link to comment Share on other sites More sharing options...
DRAWZILLA Posted October 21, 2014 Share Posted October 21, 2014 If you leave that gap between walls don't forget to call it a room, of some kind (I call them Closets, so its included in the S.F. ) or your square footage and foundation will not be correct. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now