richoffan

I went through many of the posts relating to this and came across a post from renerabbitt about the cursor jerking etc.He said trouble with the cursor is typically not the mouse but the graphics card. Sho enuf NVIDIA released an update 8/31/2021. All better. Once again you da man Rene!

Using a Logitech G502 corded mouse. Switched out to a G302 and same problem

Wow exactly why I just signed on. X13 was working fine except for little quirks like change my 8x8 doug fir posts to bronze or randomly changing a polyline solid back to concrete. Annoying but easy fix. I'm working on an extensive timber frame. Cut a back clipped section to modify rafters and beams and BAM. Cursor works fine until I highlight a CAD item I'm modifying before converting to solid and the cursor becomes unlivable. Slide over to another monitor with the plan up and everything normal.....PITA

Use a soffit. Position it where the pilaster goes. Align top and bottom at footing. Use the the material eyedropper from the wall to the soffit and the grout lines will line up. Use CAD to patch the plan view

I have a CAD line in my layers called CAD, Whiteout... set to about 25 it covers most "unwanted" lines and can always be increased if need be. Handy to block a cross as well for those pesky dimension extensions that cross. Just copy paste on the intersection.

PM Sent

As Gene said, the floor composition is in the structure tab>edit floor. You can build the floor layers similar to "building" a wall. You adjust the elevation of the materials with absolutes, rough and most important stem wall - top of footing to top of mud sill. Set your heights relative to all your structural elements and required rough height and you'll be fine

PM sent

I think the program is reading two switches controlling the same outlet - three way. Try overlaying a different outlet, receptacle, etc. and put it on its own layer so you can "white it out" - Make sure one switch goes to each hot point.

Do it all the time. Basic architectural drafting standard (at least when I learned it in the 60's) is the main entry faces the bottom of the sheet or the right. When I change to a smaller scale such as 1/8" I send as a key plan and separate into 1/4" plans at logical and clearly marked break lines

Have you tried File>Back up entire plan ?

Or where you're trying to pull the dimension draw a cad line. They'll snap to the section lines. The dimension will snap to the cad lines. If you make changes to the model you can move the line by the connected dimension

Or just go to the dbx and tell the pasted window not to include in schedule. Like Eric says if you put it on its own layer you can just turn it off in elevation... Good one Eric

Don't know if you'd call it a solution...more a work around. On your first floor copy the window go to second floor and Edit>Paste>Hold Position or CNTRL ALT & C Go to the elevation and and adjust the pasted window over the original. Remember to modify any schedule you might have. Just saw David's reply... I think he's looking for tall picture window to show on first and second.... correct?

In the elevation view I usually go to the associated layer set and change the layer - walls, foundation to dashed lines. Then if need be clean up any dashed lines above grade by overdrawing with a solid CAD line. It helps, if the design permits, to make the wall a pony wall and split at or near grade. Also, you can selectively put walls on new layers with dashed lines if that helps, Formally from Jersey. Bergen County. Exit 159 off da GSP

Again Alan I feel your pain. If we don't demand better we will only get worse. Gene has restarted the request for control over dimensions. Still not an excuse for crapsmenship

Wow.......Does a team dumb down the playbook to the weakest players or train them to play with the MVPs? I know that doesn't help and I feel your pain with the workforce. What might help is when I want anything centered it's dimensioned to a center line AND the text EQL, EQUAL, HOLD CLEAR, CRITICAL DIMENSION or some such note is added. VIF if I want to pass the buck.... If you highlight the dimension, in the dbx go to segment and you can add the note before or after the dimension. No fractions? Really people?

Save your active plan view as ...icon should be / or can be added to tool bar with edit active view and save active view... Now when its saved as another plan within the same file you can associate whatever layer set you want with the new plan. Note all the plans within the file will update so if you make a change in say foundation auto dim foundation man dim will update

Thanks Eric I will... But this is a little weird - when I use CTRL>SHFT on the wired keyboard (Logitech G710) nada. When I do it on the laptop's keyboard (Alienware R3) it works fine. Thanks again - alot easier having these side by side

Thanks Eric, Doesn't seem to work anymore. I just get the same warning about opening two. I've been using screen shots but that's growing old....

Is there a way in X12 to open Layer Display Options side by side? I want to open the dialogue for a current project on one monitor and open my profile plan dialogue on another to compare side by side and see what changes I've made and what I might include in the profile.

With much helpful input from the people on ChiefTalk I upgraded from my 10 year old machine last August to this one. It's hooked to (2) 32" Samsung curved monitors and a 5T Seagate external backup. Life is good....

For the check mark to be removed the value must be different than the default or the program reaffirms

I went through and checked all the defaults for floor / foundation / framing.... everything held @ 94 stem 91 rough. Then I moved your walls to the foundation and again every thing held. I got in the habit long ago of A) move with dimension to 1/2" off concrete (airspace) or create the foundation wall with the air space and furred wall attached. Don't know why it wasn't working for you. One thing I did after checking / setting the defaults was rebuild walls floors ceilings... Then all the room defaults held Jasonn chk 52421.zip