Is there a way to set the default for 'Cantilever Underside' ???

[DzinEye]

If you create a room the room dbx shows the material for Cantilever Underside as 'default' ...but I cannot find where to change that default?  

If you go to Defaults Settings > Floors & Rooms .... neither Floor Dbx's nor Room Dbx's will show 'Cantilever Underside' so a material can be selected.

[scottharris]

You can set that default in the Ceiling Finish Definition.  In the attached screen shot, it’s using ‘storm’.  Change it here to what you want for the initial material.

 

[DzinEye]

  On 12/11/2021 at 4:28 AM, scottharris said:

You can set that default in the Ceiling Finish Definition.  In the attached screen shot, it’s using ‘storm’.  Change it here to what you want for the initial material.

Expand  

Thank you Scott.  It appears then that there is not a way to have a different default Cantilever Underside material from the rooms ceilling finish material.  Would be nice to have that broken out as a separate default... especially for exteriors.

[robdyck]

  On 12/11/2021 at 4:22 PM, DzinEye said:

Thank you Scott.  It appears then that there is not a way to have a different default Cantilever Underside material from the rooms ceilling finish material.  Would be nice to have that broken out as a separate default... especially for exteriors.

Expand  

Shouldn't a cantilever material also have a thickness as well? A cantilever is pretty common and should have an automatic function built into Chief. It should not require polyline solids, 3d moldings, editing the wall polyline, adjusting the height of corner boards, etc, etc, etc!

[Kbird1]

  On 12/11/2021 at 4:28 AM, scottharris said:

You can set that default in the Ceiling Finish Definition.  In the attached screen shot, it’s using ‘storm’.  Change it here to what you want for the initial material.

 

Expand  

 

 

Chief sure comes up with some weird Defaults ....when is a Cantilever a ceiling ? and why would it be a Zero thickness paint layer ? ( which ALWAYS shows Z-fighting in 3D )

 

it only took what 10 yrs? to get a Polyline solid default that didn't use the Foundation material by default, so don't hold your breathe Mark

 

  On 12/11/2021 at 4:22 PM, DzinEye said:

Would be nice to have that broken out as a separate default... especially for exteriors.

Expand  

 

AMEN to that......

 

  On 12/11/2021 at 4:37 PM, robdyck said:

Shouldn't a cantilever material also have a thickness as well? A cantilever is pretty common and should have an automatic function built into Chief. It should not require polyline solids, 3d moldings, editing the wall polyline, adjusting the height of corner boards, etc, etc, etc!

Expand  

 

Exactly....

 

M.

[DzinEye]

  On 12/11/2021 at 6:50 PM, Kbird1 said:

Chief sure comes up with some weird Defaults ....when is a Cantilever a ceiling ?

Expand  

Definitely way waaaay less common than an exterior one.  

 

  On 12/11/2021 at 6:50 PM, Kbird1 said:

and why would it be a Zero thickness paint layer ?

Expand  

I have to be honest, I was a bit bamboozled by this part of Scott's response.  Like you, at first I thought that he was suggesting that we can add a cantilever material by adding another material to the ceiling finish default... but that doesn't make sense, so I decided that he just means whatever we set for the default ceiling finish is what shows up as the default 'cantilever underside' finish.  

 

  On 12/11/2021 at 4:37 PM, robdyck said:

Shouldn't a cantilever material also have a thickness as well? A cantilever is pretty common and should have an automatic function built into Chief.

Expand  

Absolutely