Adam_Gibson Posted April 15, 2019 Share Posted April 15, 2019 Although the molding will only be 1/2" thick, I assume what I'm attempting is to coffer a barrel ceiling. I've tried with ceiling planes and with polyline solid. I prefer the look of the p solid because the arch can be much more fluid if I break the arch (see close up of yucky barrel just below the more fluid one). Either way, I can't figure out how to apply molding to either so it matches the arch. Heck, I wish I could just apply cabinet doors to form the arch. Any suggestions would be much appreciated. LANZA KITCHEN 01.plan Link to comment Share on other sites More sharing options...
Adam_Gibson Posted April 15, 2019 Author Share Posted April 15, 2019 Yes, exactly! Link to comment Share on other sites More sharing options...
Chopsaw Posted April 16, 2019 Share Posted April 16, 2019 Adam, If you have any issues figuring it out give me a shout. 1 Link to comment Share on other sites More sharing options...
MarkMc Posted April 16, 2019 Share Posted April 16, 2019 On 4/15/2019 at 11:32 PM, Adam_Gibson said: Heck, I wish I could just apply cabinet doors to form the arch. Expand You can use a bow front cabinet-sides and back as just openings. Delete a few surfaces in 3D, convert to a symbol and rotate the symbol. Getting the curves right is likely easier done other ways where you can use a CAD detail to get the curves. But it can be done. 1 Link to comment Share on other sites More sharing options...
Adam_Gibson Posted April 16, 2019 Author Share Posted April 16, 2019 On 4/16/2019 at 12:23 AM, solver said: These are molding polylines. I used a square edged molding, but they could have a edge profile. Expand Eric, would you mind explaining your steps? I'm having a difficult time getting molding lines to generate in elevation view, which is where I assume you did this? Please? Link to comment Share on other sites More sharing options...
Adam_Gibson Posted April 16, 2019 Author Share Posted April 16, 2019 Thanks, Eric! I'm going to try today. I really appreciate this! Link to comment Share on other sites More sharing options...
Adam_Gibson Posted April 16, 2019 Author Share Posted April 16, 2019 I've got it! But Eric, I like the way yours looks better. Would you mind posting the plan? If not, I understand. Thanks so much! 1 Link to comment Share on other sites More sharing options...
Adam_Gibson Posted April 16, 2019 Author Share Posted April 16, 2019 You're too kind. Thanks, Eric! Link to comment Share on other sites More sharing options...
HumbleChief Posted April 16, 2019 Share Posted April 16, 2019 Great thread, great tip Eric. Thanks Link to comment Share on other sites More sharing options...
Adam_Gibson Posted April 16, 2019 Author Share Posted April 16, 2019 Thanks so much for your help. This is the idea I had in the middle of the night, and now I'm able to show my client, thanks to you! Link to comment Share on other sites More sharing options...
Adam_Gibson Posted April 17, 2019 Author Share Posted April 17, 2019 On 4/16/2019 at 11:23 PM, solver said: Looks good -- how did you do it? Expand I followed your instructions! Although, I couldn't figure out the part about a point marking the radius and using the Transform/Replicate to copy and rotate the p-solid about the point. I thought I had a good handle on that tool, but apparently not. Thank you so much! Link to comment Share on other sites More sharing options...
Adam_Gibson Posted April 17, 2019 Author Share Posted April 17, 2019 I see! That's a much better method. I simply did it manually. Once I'd done the left half I copied and reflected about the center object. My method would have resulted in hair pulling if there'd been more than a couple of p-solids to manipulate. Thanks again for the lesson! Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now