rgardner

7 minutes ago, rck-tech said:

Thank you all  but I tried that, please see attached. I must be missing a click or a pick.

Please be patient with me I am refugee from the Manufacturing Industry LOL...

 

Your lower wall is set to the same height as where I am guessing you want your top wall to be.  Maybe it should be 0" "height off floor"?  So the last 8" can be the upper wall.  Also just so you know you probably want to align the pony wall at main layer outside instead of center (just a guess).

22 minutes ago, solver said:

Pony Wall?

yup right there your easy fix.

27 minutes ago, carowe said:

Dormers.pdf

Try opening this view and selecting that wall that is a half knee wall between your dormers open it and make it invisible (or use the make invisible wall button once you have it selected.). For the other side a picture of the outside of the house may help explain what you need to do for the roof.

4 hours ago, Designer100 said:

How can I get the ramp on carport to meet level with the carport? Ramp Ideal was good. Also I have colums on rear of carport. how do i get them to show up on floor plan(tried pulling forward, but still does not work)

 

Thanks

Moheb Building New.zip

Look at the absolute elevations of each and set your ramp to it.

2 minutes ago, Designer100 said:

so any suggestions. You mean use ramp tool

How do I get the mess under each end of the carport?

 

Yes Joey was saying use the ramp tool with railings turned off and a thick base for the slope.

I personally dont understand your last question?  Do you mean how do you make the base not have a gap???  If that is what you are asking... then... Like your question last week either give it a foundation or give it a thickened floor.  Make it a patio room.

17 minutes ago, skoz44 said:

Back to Working Sets.  How are you guys using them?  I realize its a plan set that never goes to layout, but what specifically are you using it for if it never goes to layout?

Not sure if it is how most use it or even if it is the most efficient or even intended use but it is where I build most of the model in before specializing in the electrical, cabinets, dimensioning phases.  Think of the working set like a semi-all (pertinent) on layer set where you build your model going back and forth but it is a messy section where you can adjust your site, your plumbing fixtures cabinets, etc.  then you use the other views as your refined (what you send to your construction documents) views with just what you want showing including reference views in different colors/line weights & types to say show plumbing drops on your floor framing plan view.)

40 minutes ago, SNestor said:

 

@bluesparrowllc...

Plan Views are Annotation/Default Sets...so, why learn two versions of the same thing?

 

Things you can do with Plan Views you cannot do otherwise:

- Custom Reference Layer Set (this alone makes Plan Views worth the effort)

- Designate a floor for the view

- Pony Wall display control...(nothing like this in simple anno set)

- Open multiple plan views at the same time...maybe looking at the foundation and the first floor for load bearing or joist issues...or plumbing conflicts.

- Designated zoom factor

- Color on or off

 

And...you have complete control of all annotations...layers, color, etc...just like a simple annotation set. Just learn plan views...you'll be happy you did.

Well summarized Steve.  I agree plan views are the way to go.  Take the time to learn them and get over the annotation/default sets stigma.  Only caveat I would say is if you are successful already and have a good system in place where you rock the annotation sets from before and your system is well defined then maybe you don't need to learn saved plan views as it might not save you time.  But in that same token newer users who do not know what you do regarding using Annotation sets shouldn't master those first, work directly with the new tools that Chief has put out. 

But for most and especially newer users take the time to get PVs down and you will be happy you do.  My two cents only and free of charge... Happy Wednesday everyone.  Hope you have a successful week!

Import your saved plan views from your template file.

19 minutes ago, Clingie said:

I´ve had a foundation done and even if I built up the roof, the glow on the wall remains...

Other reason that happens is when you have a manually placed item which is penetrating a wall layer.  Make sure no manual p-solid or other item is going through the wall.  Other than that probably will need to upload the file to figure it out.

none of the power users are going to another site to download it to help you though so I would recommend you post the plan file here if that doesn’t fix your issue.

Do you have a floor below or a foundation?  Same question with roof or floor above?  Looks like light bleed.  Finish the model with foundation and roof even if not accurate and see if it goes away.

21 minutes ago, Electromen said:

That was my next suggestion.  I would call Apple and ask for technical support.  After troubleshooting by phone, they'll send you a box for shipping to their repair facility.

1-800-275-2273

Yeah if it is running slow on the laptop screen only something is up.  I have run models close to 200mb on that same laptop without much issue.

2 hours ago, justinorwig said:

Greg this is great info.

 

I'm using thunderbolt 3 to with hdmi on the other end.  Not sure if its 4k rated but it was a better one from Office Depot or apple I think not an amazon deal

 

Sometimes I wonder if the Magic Mouse 2 and keyboard are slow to respond.  Normally its not an issue but as I type this my mouse keeps disconnecting and re connecting

That action points to some disruption of signal which is also very sensitive to how your desk is setup.  

But that sparked a memory of something I read in an Apple forum where someone was having some issue.  I am remembering vaguely something about the 2019 having some difference with the usb c on one side versus the other.  Try something funny and see if you switch to ports on the other side of the unit if it makes a difference.  There was something about how some were receiving more power that the others...  can’t recall exactly but worth a shot.

Sorry would need more information.  Plus remember to upload you need to have the chief file closed down and out plus chief itself closed.

If you are just trying to remove an as-built layout box from a layout simply find the box select and delete.  But that probably is not your issue.  More explanation?

39 minutes ago, ChiefuserMathews said:

how could you get that molding line for middle rail?

Draw it right on the railing and add the molding and set it to the middle.

35 minutes ago, Renerabbitt said:

Your knowledge has no bounds.

Was thinking the exact same thing!  Who would know that off hand.  Michael thanks for always helping us with these random issues.

Probably best to make a custom panel.  But a quick way to get what you want would be this way.  This is an 80" paneled railing with a molding line for the middle rail.  Took about 90 seconds.

Did you try manually dragging the column size?

There is a way to set it so that chief uses the proper gpu and not switch back and forth if on battery power.  Cant remember exactly but I did this with mine.  Sorry not with my laptop at the moment to open it up and try.  I don't do much traveling right now with covid and all.  But if I remember right you go to finder right click the app, get info and it is in there.  I also think there was two ways to switch the graphics card and one was with the power as well which overrides the other option if you are on battery power...  (fuzzy memory about it all when setting it up.)  If I remember right @johnny had this same issue when setting his up and figured it out in a thread.

1 minute ago, justinorwig said:

Thanks everyone. I've tried all and Still no luck.  And CA tech support can't replicate the problem when I send in various files that have the issue.  Looking for that elusive loose bolt

 

Does anyone run eGPU with a matchbook pro?

I was running one with my previous 13” mb pro but it honestly used the same GPU as in your 16”. Which is super capable.  I am guessing it is something in your template slowing it down.

I have that same laptop and have not seen those issues.  I don’t have it handy right now to open up your file but have you checked to see if you have all of your labels layers on?  That is also a famous issue with slowing things down.  Otherwise I would send to tech support as that computer runs Chief really well!

2 hours ago, Kbird1 said:

Methinks you blaspheme   

 

 

M.

Agreed! haha 

BTW I believe in X10 you can still individually select walls and frame them individually (don't recall for 100% right now and not at computer again)...  But I think what Michael was talking about was the wall framing issue at the window.  Pretty easy to open up that one wall and reframe around the new window and go on instead of spending a considerable amount of time to fix it automatically.  Now from my side I totally understand as my OCD wants a perfect Auto everything model.  I still end up having to give in on some and fix it instead of letting it do it automatically...   But generally that is a stairs or a roof thing in 99% of the cases and it is just the way Chief works on that particular item where it is good for 99.9% of the cases but not the %0.01 of cases that particular model falls into... 

Looks like a tall panel railing with a middle rail to me.

9 minutes ago, SusanC said:

Update:  Thank you for the info Ryan.  I exchanged the NVIDIA for an AMD and everything works great!

Glad it worked.  I worked quite some time with my e-gpu and even traveled with it.  It surged with a power spike in Mexico and they told me it had built in protection so it should have not done that and they replaced it free and clear after 18 months of use.  I ended up upgrading my laptop at that time and just turned around and sold the new unit but it worked quite well with a 13" MBP.  That all being said I love my new 16" as it seems to be the sweetspot of portability mixed with enough size.

Didn’t go to your model but to answer your first question you can select one wall and reframe just that wall.  Note you will need to permit it (ie unselect retain framing before and respect it after.). 
 

Purely a guess based on your description but possibly your walls heights are different because you have different ceiling and floor heights in the rom dbx and you made it look how you want it by possibly dragging the walls in an elevation or 3d view?  If that is the case select all of your walls and in the structure tab of the dbx select default wall height top and bottom.  The go to your preferences and set your 0 floor ceiling height (assuming they are all set to use defaults). Same on first floor.  But just A guess.  I am not at my computer but doing pool time on my phone.  Maybe someone who is at their computer can open the plan file and check if my guess is right?

3 hours ago, stevenyhof said:

Very possible! Now I need to figure out how to turn it back on - the browser is not letting me upload my plan. 

Maybe I need to go back to an archive.

Michael, I think I need to retain your services for things like this. 

You have to have the file closed out of Chief before you can send it or upload it anywhere.