moving mouse in section lags

[SHCanada2]

seems to happen on residential template as well.

 

only happens in section views. plan views are fine.

 

auto build framing is off

 

Anyone else seen this? its pianfull when trying to move something to a specific spot, because you have top move the mouse and then wait for CA to catch up

 

Its been happening for awhile. I updated my video driver a couple days ago, but its no better

 

see attached

'

[ValleyGuy]

10 minutes ago, SHCanada2 said:

seems to happen on residential template as well.

 

only happens in section views. plan views are fine.

 

auto build framing is off

 

Anyone else seen this? its pianfull when trying to move something to a specific spot, because you have top move the mouse and then wait for CA to catch up

 

Its been happening for awhile. I updated my video driver a couple days ago, but its no better

 

see attached

'

 

I also experienced this. I did a complete shut down and rebooted my Mac and it seemed to clear up the glitch.

 

[Joe_Carrick]

I'm not seeing this problem.  What rendering mode are you using?  What LayerSet?

[SHCanada2]

12 hours ago, Joe_Carrick said:

What rendering mode are you using?  What LayerSet?

i just drew 4 walls on the stock residential template, then a back clipped cross section, so the stock layerset assocaited with that.

 

But I did try before that, on my own plan switching to the all layers off layerset, so nothing was showing, and it was still happening. But the plan view is always fine

13 hours ago, ValleyGuy said:

I did a complete shut down and rebooted my Mac and it seemed to clear up the glitch.

how often are you rebooting? I get windows crashes on a regular basis when I have PBR opened (never used to before say 5 months ago), so for this reason the computer is getting rebooted on a fairly regular basis. but I will try and do a clean reboot to see if it changes anything

Edited 6 hours ago by SHCanada2

[ValleyGuy]

42 minutes ago, SHCanada2 said:

i just drew 4 walls on the stock residential template, then a back clipped cross section, so the stock layerset assocaited with that.

 

But I did try before that, on my own plan switching to the all layers off layerset, so nothing was showing, and it was still happening. But the plan view is always fine

how often are you rebooting? I get windows crashes on a regular basis when I have PBR opened (never used to before say 5 months ago), so for this reason the computer is getting rebooted on a fairly regular basis. but I will try and do a clean reboot to see if it changes anything

 

It only happened once and I am not quite sure what triggered it. I don't use PBR, ...well I do click on it once every year or so - I'm not sure if I hit the button the day that I had the lag issue or not. The only computer crashes I have are if I leave CA open (no plan or layout open) too long without using the program. Example: if I close down the plan but don't exit the program overnight, then in the morning I will see where my computer rebooted itself with a 'Kernel Panicked' reboot report. But no crashes while I'm using the program.

 

On a separate note, I just had an error the other day to which I followed CA protocol and sent in a bunch of information. It too was on a cross section elevation; just updating a view port on the layout. CA Helpdesk couldn't find or replicate any issues and I haven't had any issues since. Both the lag issue and the error code seem to be one-offs.   I only loaded up X17 a couple of months ago but have had two strange things happen as well as a few Kernel reboots.

[Joe_Carrick]

Evidently this only happens on a Mac - and then only under certain conditions. 

 

[SHCanada2]

37 minutes ago, Joe_Carrick said:

Evidently this only happens on a Mac - and then only under certain conditions.

well maybe if it happened in 1988 when I last used a mac ...

[SHCanada2]

i rebooted, same issue. 

 

Tried to see if it happend on X16, and got this error when just starting X16 without opening anything

 

going to try and roll back the driver

Edited 3 minutes ago by SHCanada2