-
Posts
2856 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Everything posted by ACADuser
-
How about an SKP file? https://www.arcat.com/company/whirlpool-corporation-36529/bim/jenn-air-ventilation-78007 https://3dwarehouse.sketchup.com/search/?q=range hood
-
Perry How do you remember all those little tricks?
-
You did not like the Chief "Low Profile Hood" in the catalog?
-
Different Stair and Deck Railing framing methods?
ACADuser replied to SPSEngineering's topic in General Q & A
From my cheat sheet index https://chieftalk.chiefarchitect.com/index.php?/topic/1199-deck-post-fascia-mount-possible/page-3#entry42799 https://chieftalk.chiefarchitect.com/topic/13653-fascia-mount-railings/ https://chieftalk.chiefarchitect.com/topic/5306-deck-railing-post-fascia-mount-tip/#comment-46137 -
As Michael said, click the wall followed by the dimension text. If it does not open for edit the dimension is not snaped to the wall.
-
Eric, Nice solution, very accurate. Thanks
-
I was preparing a view to send to the structural people as they can not seem to understand the desired slope of the roof. So I made it obvious with the arrows. They can be hard headed at times. I took the columns down to the foundation pads as they don't rest on the sidewalk. Can you snap to the poly solid surface? I could copy in place & drag the bottom to snap to the surface.
-
When a column or other solid penetrates a slab there are no lines at the base when you send to layout. How do most of you deal with this? I was thinking holes in the sidewalk might be the cleanest.
-
Currently our code says: R806.2Minimum vent area. The minimum net free ventilating area shall be 1/150 of the area of the vented space. I think at one time it said floor of the attic. So if you had cantilevered trusses would you include soffits in that area? I think I've used the exterior face of the exterior wall for years. I seem to remember the ceiling delimiting the attic & I used the interior face of the exterior wall. Maybe 20 years ago. Question is what defines "area of the vented space"?
-
That bears repeating! Open up the walls you intend to use and make sure the material thicknesses are what you want. Make sure you pay attention to the MAIN layer, and the exterior layer. For example some like frame walls with sheeting (OSB or Plywood) to align with the face of the foundation block. Some like the framing to align with the face of the foundation block. In this case the sheeting will need to be on the Exterior Layer. Then Wall Setting within the same dialog, the three pull downs should usually be the same. This is important for keeping walls above on the next floor aligned properly. If you learn these setting up front you prevent a lot of head scratching until you do. Enjoy.
-
Mark, you figured it out. It was the extra floor. All is well now. Thanks
-
Thank you Dan, that fixed it.
-
That would be too easy. Try again
-
I've had this issue on and off for some time. The plan original file was several years old, a new similar house. Why are some of the foundation walls filled & others not? Thanks Foundation.zip
-
Just tried MS Edge & no issues. Looks like the Chief website is using a larger font. I am able to change Firefox font size & it changes for other web sites but not for Chief.
-
Not sure if this is the correct forum. I'm seeing this issue for the past week or so with the web site. The frame overlaps the one above. Do others have the same issue?
-
Rob, That's a great tip. Unfortunately, I did it the hard way Gate Steel Slats.calibz
-
I need to add a door / gate to the 42" high guard rail & it needs to match the railing. See the detail below. Is the best way to handle this to make solids into a symbol for a door?
-
I too would like a check box for the cantilever truss. This would disable "Automatic Birdsmouth" check box It would place the bottom chord on the top plate. The rooftop chord would be a function of the overhang, sub-fascia, and perhaps chord member heights. I use Cantilevered trusses most of the time.
-
To upload a plan file you MUST close the file in Chief as Chief locks the file while in use. I think you need to create a "Truss Base" to solve your truss issue.
-
Try turning off Automatic Height in the upper stair.
-
Maybe if you search the catalog for Shed? Or see these: Screen Porch, make a screen door https://chieftalk.chiefarchitect.com/topic/26951-screen-porches-the-easy-way/ https://chieftalk.chiefarchitect.com/topic/19253-video-lesson-screen-porches-railing-walls-and-panels/ https://chieftalk.chiefarchitect.com/topic/19253-video-lesson-screen-porches-railing-walls-and-panels/?do=findComment&comment=158022 https://chieftalk.chiefarchitect.com/topic/19714-video-lesson-more-screen-porch-info/ Porch wall & moldings https://chieftalk.chiefarchitect.com/topic/20048-video-lesson-front-porch-with-columns/?do=findComment&comment=163680 *** Good Porch video *** https://chieftalk.chiefarchitect.com/topic/27511-suspended-porch/?do=findComment&comment=220741
-
Sometimes a room divider wall to nowhere will help with the intersection. Pull the one foundation wall back to break the connection. Drag a room divider wall from outside the house to intersect the foundation & then pull the other wall in to intersect. Tough to explain without a plan.
-
Maybe: https://3dwarehouse.sketchup.com/search/?q=rope column https://3dwarehouse.sketchup.com/search/?q=twisted column https://3dwarehouse.sketchup.com/search/?q=spiral column
- 5 replies
-
- spiral carved column
- post
-
(and 1 more)
Tagged with: