StephenGreene

i have tried this multiple times, EXACTLY as they mention, but it never works. instead of spread out along the arc, they end up wadded up in one place. it's too bad, this isn't an automatic feature -like lintels.

you are on another level my friend.

wow. that's almost hard to believe. i did one plan in that and went back to 12. no offense Chief, but 13 was crap. 15 is great. should catch up to that.

lookout is the only term i've ever known. and i've never in my life heard it called an "outlooker". interesting.

great idea, Steve. i didn't even think of making that area a "room" with invisible walls. that certainly fixed the problem. thanks for taking time to help with this.

customer wants the porch to extend one foot out (on the front only) from the porch beams/wall. when i move the foundation out 12", the frieze and soffit disappear. i know i could make a soffit and frieze from solids, but there has to be another way. right?

Dude, you are awesome! Thank you again, for taking your time to help me with this.

Thanks, Rob, that did it! 1. I had the wall heights set at default, I was just trying anything to make the lines disappear. 2. same as #1 3. Yes, I always do this. 4. Good idea. Will definitely do this. 5. Not exactly sure what you mean by this, but I do know what double lines you are talking about. I had to make it a pony wall to get the brick height correct. 6. THANK YOU AGAIN! That was driving me nuts.

i did as Rob suggested, moving them all to the second floor, they disappeared and then came back. I'll definitely send it in.

Hi Rob, thanks for looking at this. I did just as you did and the lines were gone. For a while. Then I refreshed the layout and they were still there. Went back to elevation view and they had come back. Ugh. Just wondering if they are still visible on yours.

I've done them like this in the past using solids. I used this method after watching one of @Renerabbitt's videos on youtube. So....I'm going to blame him for the batts running up so high. Thanks.

no idea what is causing the lines on this elevation view. i have tried all sorts of things to get this to go away, but no luck. sometimes, it's one line and sometimes two lines appear. plan attached. CYStracener.plan.zip

i've had the same problem with a floating soffit protruding through the roof as shown in your top pic. i've found that an easy way to fix that is by making a small notch in the roof plane. this eliminates the floating soffit and the "boxed eave" at the other end of the roof.

Here is something I drew up in just a few minutes with three different ways to do the overhang on a multi-pitch roof. Usually, I just hit auto build with all the roof pitches set at the lowest pitch, then lock the shadow boards top height and then raise the pitch on the adjacent roof plane. That method keeps all the overhangs the same, but it does throw the hip off of center of the corner. You can also shorten the overhang of the steeper pitch, but I never do that. Another method is to have steeper pitch set on the plate just as the lower pitch but with no tails and a short shallow pitch roof plane at the bottom. This way leaves the hip centered on the corner and probably the method preferred by most framers because they don't have to figure out how far over to move the hip or valley and how much to raise the seat height of the higher roof pitch. Multi-pitch roof plan.plan

overhangs can still be exactly the same with different pitches.

I bet that as many as half the plans i draw have multi-pitch roofs with the fascia the same height. and i built a ton of them back in the day. all one has to do is raise the fascia of the steeper roof to match the fascia of the shallower roof plane.

same here. and 9' studs are 104 5/8", 10' studs are 116 5/8" etc.

no, no response from anyone.

yeah, i once got a downvote for helping someone with their roof.

Thanks, Joe. 24' fir and/or LSL is not hard to get around here, though it is expensive. but yeah, framing that would not be easy. scaffolds or SkyTrak would be the way.

Thanks, Ryan. I suspected as much but wasn't sure.

Thanks, but I don't see where that answers my question.

Full two-story house. Twelve foot ceilings on first floor and ten foot ceilings on second. Living area full two-story height (23'-7") with two exterior load-bearing walls (roof). Best I can tell, code says you can go full 20' with 2x6 framing. What is code for 23'-7" exterior load-bearing walls? 2x8? or 2x6 @ 12"O.C.? Thanks.

yeah, i'm not exactly thrilled with the new library set up myself. it can never find anything when i go to search.

Thanks, David. I had done this before and figured it out but my mind just went blank this time.