-
Posts
6052 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Posts posted by HumbleChief
-
-
Or better yet, how to draw ONE 5 ft. wall? If I draw a wall and hit the tab key, enter 60" the wall ends up at 5' - 2"? Not getting something.
-
Yeah I know, lamest question ever but if I can't seem to get (3) 5 ft. long walls at 45 degree angles. Oh and I'd like the walls to be measured from the outside not the inside.
-
15 minutes ago, Joe_Carrick said:
Just move the special sized rafter down the thickness of the roof plane. You can put them on another layer and use different materials.
That worked a treat Joe!! Thanks
-
6 minutes ago, Joe_Carrick said:
Just move the special sized rafter down the thickness of the roof plane. You can put them on another layer and use different materials.
I'll try that too Joe, Thanks
-
2 minutes ago, TeaTime said:
I'd just move that Soffit to the Beam layer so it'll look like the beam it's pretending to be.
Just in case you have other soffits around.
*can even put it on a Framing Schedule if you need!
Interesting....Thanks
-
Just now, Chopsaw said:
Sure. ALDO > Cabinets, Soffits > Line Style:
DOH - Thanks again!!!
-
2 minutes ago, TeaTime said:
I guess it depends on which way you want them to follow the pitch?
Roof Beams will inherently follow the slope up, and generate underneath a sloped ceiling, but if you're going sideways, most framing won't rotate to match the angle.
ex: this was just posted yesterday:
So depending on the situation, 3D Solids very well may be easiest.
Thanks Tea Time but the faux beams will run perp. to the beams you've shown.
-
Looks like Soffits will work great as they follow the roof. Is there a way to change the line style from the default dashed line?
-
7 minutes ago, Joe_Carrick said:
You should be able to draw a single rafter and change its size & vertical position.
Thanks Joe, these 'beams' will be faux beams that will occur below the roof framing and T & G ceiling surface. Can't see how to use a rafter?
-
11 minutes ago, Chopsaw said:
Soffits can work depending on the situation.
Thanks Chop.
-
For a faux beam look, or is it a P-Solid job instead?
-
Thanks DB, could have sworn I tried that - too easy and thanks for the help.
-
In plan view there's "Snap Unit" which I have set to 1/16" to move for very small adjustments. Is there a similar setting in Layout to reposition layout boxes? It seems to be set on approx. 1" and don't know how to change that setting. THANKS
-
Hey Joe, If this is for the City of Solana Beach I just submitted one set for planning and was only asked to remove the structural and T24 sheets then saved the layout as "Client Name/ Planning Layout" and submiitted to planning. Hope that helps.
-
THANK YOU Rene!! The stretch was following the sloping Terrain!
-
Is this expected behavior?
-
1 hour ago, Renerabbitt said:
Graphics card, just industry short hand
DOH, Thanks....
-
16 hours ago, Renerabbitt said:
Switch to GFX card based PBR raytracing. Rendered in under a minute:
Apologies Rene but what is a GFX card?
thanks
-
1 hour ago, Chrisb222 said:
Lol. You probably know this Larry, but you can also unlock that layer and manipulate the poly lines for the trim. Just sayin'
Thanks Chris. I almost never use shadow boards and checked a dozen videos and knowledge base etc. and had no idea they actually were on their own layer so of course I searched layers for 'shadow' got nuthin' went through a dozen more posts, then turned on 'all layers' and there they were but then had to go through each layer......sheesh. Thanks again!!
- 1
-
YES THEY ARE!!! Roof, Trim. There's an hour I'll never get back.
Thanks
-
Or am I just missing how they work? Can't get them to show but don't know why.
Thanks
-
32 minutes ago, VHampton said:
Bless her heart...
Are you from the South by chance?
-
7 minutes ago, VHampton said:
Next week for sure.
That's adorable...
-
4 hours ago, DRAWZILLA said:
Larry notice when you open X15, the heading doesn't have the word beta anymore. Chief has been doing that in the final beta for years. there will be a final update before it officially releases.
Thanks P.
How To Draw 3 Five Foot Long Walls?
in General Q & A
Posted
Hey Mark, I really want to thank you but I have no idea what resize about interior surface means or how it might work?