Sign in to follow this  
Oostin

Missing Fascia Board

Recommended Posts

I am using chief architect version 10. When I use the "create a hole in selected object tool" on my a-frame's roof, it deletes the fascia board. Does anyone know how to prevent this>?

Share this post


Link to post
Share on other sites

Are you using Version 10 or do you really mean X10?

Share this post


Link to post
Share on other sites
On 3/21/2019 at 12:59 PM, tommy1 said:

Are you using Version 10 or do you really mean X10?

X10, sorry.

Share this post


Link to post
Share on other sites
On 3/21/2019 at 9:01 AM, Oostin said:

it deletes the fascia board

 

You will need to post images and probably the plan file for an answer.

 

No one knows what fascia board you are referring to.

Share this post


Link to post
Share on other sites
On 3/26/2019 at 1:29 PM, solver said:

 

You will need to post images and probably the plan file for an answer.

 

No one knows what fascia board you are referring to.

image.thumb.png.ba4bd80b88d59daaffb742111eb56e23.png

Share this post


Link to post
Share on other sites

Oostin, you do need to post the plan as Eric said. If you do, just be sure to save and close the plan before posting.  If the file is too large you should be able to zip it.

Share this post


Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
Sign in to follow this  

  • Member Statistics

    27850
    Total Members
    6254
    Most Online
    heidimm
    Newest Member
    heidimm
    Joined
  • Similar Content

    • By ilastu
      I successfully imported the floor plan for a house from a dwg file, however I have not found a way to convert the roof drawing into 3D. Is there a way to do that? I am using the X11 version.
    • By SpeleoWorm
      I have created a number of different wall types to show proper dimensions (i.e. when one side of the wall is 5/8" Type X and the other side is 1/2" drywall) as well as to calculate the correct material counts and to show the proper information in the schedules.  Unfortunately doing that seems to have a down side...it changes the framing as if they were separate walls instead of the same wall with different materials on them.  I have seen the following side effects (colors refer to screenshots below):
       
      (Green Arrow) In unfinished rooms such as an attic storage space which only has a subfloor but no drywall, the walls get pushed up into the rafters by what appears to be 3". (Red Arrows) The floor joists and top/bottom plates are cut in the middle when they should be continuous pieces of wood.  In addition, you can see that the walls which are produced are not boxed at the end...the top & bottom plates stick out at the end. (Purple Arrow) Parts of the gable wall are not created.  In this case you could argue that it is not needed, but if a builder makes a wall he is not going to leave a hole in it. (Blue Arrows) An extra stud is added to a room that has no drywall, and therefore doesn't need nailer studs.  In addition, it looks like the other stud needed as a nailer for the finished room in the middle is missing from the plan view of the framing (see 2nd screenshot).  
      Am I doing this all wrong (creating separate wall types), or is there a way to use them and fix (any of) the issues I mentioned?
       
      Thanks in advance for any help!
       
      PS - I am a little surprised that the wall finish is not part of the room settings (like the floor & ceiling already are)...that would allow you to have continuous walls and still have different materials in each room (i.e. greenboard in the bath, 5/8" type X in a garage, unfinished in an attic, etc.
       
        
      Example of Wall Issue.plan
    • By ChristinoDesign
      We're trying to figure out how to change the angle of pendent lights on vaulted ceilings. When we create the ceiling angle, the lights follow and aren't angled properly. How do we change the lights so they go vertical rather than at a tilt?
    • By Alyssa5
      Hi,
      I am using Chief Architect X8 on a Mac.
      I am having trouble with roof planes - I want to be able to change the baseline height but it keeps defaulting back and won't alter.
      Yet when I open the same file on another computer I can change it
      Any suggestions?
       
      Thanks
    • By josiemlittle
      Hello, I’m needing help lowering the roof. I’m trying to make a 50x80x16 shop with the pitch lower than the default gable height. I’m new to this and I’m hoping this software will help build our dreams on our farm. I want the look of the attached photo with the front being the 80 ft side.