ChiefuserMathews

Thank you Eric for your reply. It doesnt work and I don't know how to do the custom muntins

Hi Eric, Thanks for your quick reply. I dont have that option it is greyed out.

Hello, I am trying to add a side lite to a door as shown in the attached image. I dont see an option to set the height of the lites. Could some one help me out how to achieve it. But this is what I get with 2 horizontal lites

Hi, How do I show a 3 way connection switch for a light at the top and bottom of the stair. Currently the 3 way switch can be shown only on 1 level. unless there is an another option. Thanks for the help

Is there an option or preference where you can set where the end of leader line will align with the text. I prefer to be on middle of top line either left or right depends where the text are placed. Currently if the text are wrapped the end of leader will move to middle of the wrapped text box. Where is the setting where I can change it?

Jerry and Eric. You guys are awesome. As Chris mentioned didn't know about that option. That exactly what I was looking for. Great help. Thank you. Enjoy your day.

Here I am trying to cut section of a deck. (Image attached). Unfortunately garage wall is in line with the deck edge. (plan view image attached) which I don't want to see in my section view. Is there a way I can hide or clip what I want to see? Garage wall is hiding the stair behind. del1-219003.pdf del-219003.pdf

Thank you to both of you for your prompt reply. have a great day

I am modeling a deck. The engineer has specified to use 3-2x10 beams. How do I get that configuration?

I am trying to model a below grade entrance to a basement with a concrete stair. Currently the top of the foundation wall for the stair is 15 inch above grade. I want that to be only 6 inch above grade.. How can I achieve that? I am not sure where is it getting that information of 15 inch. Thanks for the help

What does that mean?

I am trying to model a below grade entrance to a basement with a concrete stair. Currently the top of the foundation wall for the stair is 15 inch above grade. I want that to be only 6 inch above grade.. How can I achieve that? I am not sure where is it getting that information from. Thanks for the help

Thanks everyone. I found it. It was part of a series of video # 6045, starting at 12 min. thanks again

Thank you. I found that. In fact that's not what I was looking for. No the egress type. But with the window well.

Thanks Eric. I tried that. I could not find one, hence I posted in the forum

Hi I am trying to create a window well for a basement. I have seen a training video in the past from Chief Architect. I tried searching for it and could not find it. Any help is much appreciated Thank you

thank you Eric. You are awesome. Thats what I was trying to achieve, but I didn't know how to do that. Great job.

Eric, are you creating a new wall type? or how do you achieve that?

Thank you Eric for your quick response

Hi, I am trying to add a railing to the concrete slab. Top of the slab is 2'-0" from the garage floor. When I add the railing it goes to the garage floor level. How do i raise to the the slab level? How do I add the full height wall on top of the slab, so that it can be supported on top of the slab? Attached is the image and plan for easy reference 218009-opt-10-Forum.plan

thank you.

Hello, when I doing the auto interior dimension, why am i getting exterior dimensions as well?

Hello, I am trying to add a stair to the basement, opening a floor for the stair to pass thru. When I use the auto stairwell option it does not open the adjacent floor, it partially open floor on one side of the wall. I had to add a rails on the upper floor to open the floor for the stair well. Plan attached for reference. Now how do I cut the joist to make room for the stair to pass thru, which shows in my 3D view? how do i achieve that? 218011.plan

Thank you Eric. that worked, but only thing it jumped inside the stair, which I had to move. its ok now. thanks again.

Attached is the plan as discussed. please advise. 218009-opt-04.plan