-
Posts
1261 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Everything posted by Steve_Nyhof
-
That did it! - It must have been a bad symbol. Thank you Eric!
- 7 replies
-
- molding distortion
- column molding
-
(and 1 more)
Tagged with:
-
Got it. So maybe I have a bad symbol. I will use the plan to make a new symbol and give it a try.
- 7 replies
-
- molding distortion
- column molding
-
(and 1 more)
Tagged with:
-
Thank you Eric, I can see you fixed it - but I am not following what you are saying. "The single column plan" ?
- 7 replies
-
- molding distortion
- column molding
-
(and 1 more)
Tagged with:
-
I put new columns on the front porch - all worked fine. Might have been a glitch. Now onto the rear which is a railing wall and beam.
- 7 replies
-
- molding distortion
- column molding
-
(and 1 more)
Tagged with:
-
Offset is set to 0" - on the rear porch. The front porch are stand along columns - no rail wall. I am using a divide wall - maybe that is doing something to the columns???
- 7 replies
-
- molding distortion
- column molding
-
(and 1 more)
Tagged with:
-
On the house file I uploaded, I did not include the front porch header - not drawn yet. I am making that now. But, I am finding something very strange going on with my columns. Now I am thinking I have a funny insertion point or making the columns wider is doing something funny. They are drawn 10" square on the column and the molding outside of that. So I am making it larger so that my columns are 12" square (roughly) for this plan. The plan view shows they are centered, but the 3D are offset. Hmmm, offset... I will need to check that...
- 7 replies
-
- molding distortion
- column molding
-
(and 1 more)
Tagged with:
-
For the time, I made my beam width wider - 14.5" - this increased the width of the trim to match the roof trim. I like this and makes sense to me. So all remains is the column molding distortion.
- 7 replies
-
- molding distortion
- column molding
-
(and 1 more)
Tagged with:
-
I have two questions, both in this same picture... My column molding is distorting on the top. On the rear of this house I wanted to learn more about making my header/beam using a railing wall and my columns I made. I'm liking this better than on the front of this home where I create a molding to make my header/beam and then add my columns in. I even made my columns smaller and places symbol columns over the top of the existing built into the railing wall, but they would not fit over the top - conflict - and also did the same distortion on the top molding. The other is the roof frieze board. Looks strange. I figure there may be something I am missing to make this look right. I was very careful with my dimensioning of the rail wall and my roof. I even tried the using "Edit Wall Layer Intersections" tool - but that did nothing. That may be more for how a plan looks. I also tried the "Wall Intersection" options in Structure. The file is too large to upload here so I will include a link to the file from my google drive... https://drive.google.com/file/d/1Ir7TdOUleweaC7DFxXqp3hEvQ2eKn-K7/view?usp=sharing Thank you, Steve column_standard_post_10-02.plan
- 7 replies
-
- molding distortion
- column molding
-
(and 1 more)
Tagged with:
-
Thank you Michael! That did work... I used 100 and red just to show it here.
-
I must be doing something wrong. I will come back to this later...
-
I'm not following... I put a switch in the stairs and opened the DBX - then re-label it... then .... ?
- 10 replies
-
- 3 way switch
- three way switch
-
(and 2 more)
Tagged with:
-
Very good! Was thinking maybe something simple like that. Thank you
- 10 replies
-
- 3 way switch
- three way switch
-
(and 2 more)
Tagged with:
-
I'm making an electrical plan and trying to figure out how to add my electrical line to my light fixture over the stairs - shown on the main floor. So I have a 2 way switch at the bottom and top of the stairs.
- 10 replies
-
- 3 way switch
- three way switch
-
(and 2 more)
Tagged with:
-
I just seen that when I was messing in layout. So when you send a view to layout, check the box for Pattern, and then you can control it? In layout, the option was there to change the Pattern line size, but changing it did nothing. But maybe I am supposed to send the view to layout checked and that offers what I may need. I will try that. Thank you!
-
I will most likely leave them as all the patterns (textures) are already set to 0 - So whenever I would change siding I would need to mess with this. I think I was just use to them being darker and more uniform, so I think I just give it time to grow on me.
-
That did it. So out of the box the patterns seem to be set to 0 ?? I will do some digging in help on this - Thank you again!
-
Thank you Eric! I am still learning the lingo. I was in that DBX but did not see the line weight. I will give that a try
-
They must me like 0 or 1 because no matter how far I zoom up, they stay thin, while others get thicker
-
I'm in plan view - I have not messed with any settings in layout
-
My roof and siding plot too thin. Not sure if it shows up in the photo
-
I should add that I am working in my Elevation Layer Set to try and change the hatch lines.
-
Really nice stuff Joey! I'm trying to find the layer that controls my elevation hatch lines. They are too light/thin. I tried the Walls, Hatching and Walls, Normal but that does not change in the elevations. Anyone want to guide me to the right layer, please? And sorry Joey about getting on your case when I first got into Chief. You were right about letting ADT go. I have been drawing a number of houses now on Chief and when I need to go back to ADT for a condo project, I get all confused and actually like Chief better - in a lot of ways!
-
My Chief Skills - Screened Porch Library
Steve_Nyhof replied to SNestor's topic in Offering Services
Highly Recommended! I saved a ton of time purchasing Steve's porch kits/tools/options. I have been using CAD for over 30 years now and am very capable of figuring this out in Chief in time. But why? Just get creative now using what is already created for you! I add screen porches on my designs all the time here in Western Michigan. More than enough options are included which offer that perfect touch no matter what style you are designing for your client. -
I should have expanded my comment. I am not rotating because it does not help me. Just commenting on the fact that the rotate text in the text defaults is related to rotating the plan. I am trying to find a way to maintain the text orientation when I reverse (mirror) the plan. Is there any option to maintaining the text when reversing the plan?
- 4 replies
-
- reverse plan
- reverse text
-
(and 1 more)
Tagged with:
-
I do see that when rotating a plan using the "Rotate Plan View..." tool, it works. I may have rotated a plan less than 10 times in 40 years. I have mirrored a plan many times.
- 4 replies
-
- reverse plan
- reverse text
-
(and 1 more)
Tagged with: