yusuf-333

creating a stair that follows terrain, video by Yusuf.

Recommended Posts

Isn't it OK, the sound. though I am not native speaker, it is better actually now. You know I am fast learner.

This method helps to understand the relation ship b/n the stair risers and contour intervals. And at the same time the plan view of contours with thread depths. This is an other good example on, why programmed workflows are important to addapt in the different stages of the learning curve.

Share this post


Link to post
Share on other sites

Yusef,  it is very difficult to understand. It looks good,  but I could not get the gist of what you were you were trying to teach us.

Share this post


Link to post
Share on other sites

Yusef, it is very difficult to understand. It looks good, but I could not get the gist of what you were you were trying to teach us.

Oh..humm are you kidding Scott? That is shame on me. I thought it was clear. OK this was following a last time's discussion on this issue.

https://chieftalk.chiefarchitect.com/index.php?/topic/6856-how-to-build-exterior-stairs-that-follow-the-terrain/

Share this post


Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now

  • Member Statistics

    28449
    Total Members
    9156
    Most Online
    David_Montreal
    Newest Member
    David_Montreal
    Joined
  • Similar Content

    • By rfantclt
      Fellow More-experienced CA users,
       
      I have drawn as-built plans of a house for a renovation/addition project in CA v.12.  I recently received the final survey from the surveyor with property lines, major and minor contours, the building footprint, and other typical survey information.  I imported it from .dwg as a .plan file  with layers for terrain perimeter and terrain, and converted the terrain using the convert tool to make it 3D.  It shows up with terrain. Yay!  Now I'm not sure of the next steps:
      1. How do I bring the terrain into the building.plan?
      2. How do I set it in place - using a Place Point or Point Marker at a corner of the house?
      3. The survey elevations are in the 650' range so how what do I do to place the terrain relative to my house (1st floor 0.0)?  This house has a walk out basement, if that matters.
      4. I copied in a 2D version of the survey to use in plan view (on layer CAD, AS-BUILT SURVEY).  When I send it to layout, the house floor plans are obscured and the secondary contours didn't come in - admittedly, this is a previous version of my survey attempt and I've since remapped the survey layers.
       
      I have also attached the house plan, if that helps.
       
      Thanks for recommendations from this group, as I've watched numerous videos and couldn't find any that addressed this process.
       
      Rebecca
      CA Premier X12
       
      Zoutewelle FINAL SURVEY.plan
      Muhs Existing.plan
    • By MN_JohnH
      I know this has been talked about before but I can not find it and I can't figure out how to do it again.
      I have a house drawing and I have the terrain drawn and I would like to orient the house differently on the terrain. I want to keep my house drawing square with my plan so it would need to be the terrain itself that has to rotate. I can rotate the terrain perimeter but that doesn't rotate the elevation lines etc. When I select the perimeter and all the elevation lines, i am not able to rotate the whole thing.
    • By decorators3
      Hi 
       
      I am building a foundation but in camera view there is a hole under the foundation but no terrain.. ???!!
    • By Steve77
      Hi There,

      I am a current chief architect user and have a question in regards to the contour tool and driveway tool.

      I have a plan that has a sloping site that I am trying to accurately portray in 3d for both client and the Local Council.
      From the road front the site slopes left to right and from the back to front.
      (I have attached Images shown what I currently have)

      My question is there something that I am missing I have also tried in elevation converting/extracting a polyline solid but it doesn't quite work.

      I have attached a link to the 3d viewer but can add a plan if need be.   https://3d-viewer.chiefarchitect.com/go?share=503392208525732