wncbw7

Thanks, that did it.

Filled out signature. Did you have a suggestion re my question?

I am trying to create a relatively simple cabinet door with a flush center panel. I created 2" wide rails with a 3/4" reveal. I made the symbol and sent to library with no problem. However when I apply it to a cabinet the door is rescaled and the rails become 4" with a 1" reveal. How do I keep the rails consistent the way cabinet door typically work???

Is there a way to make the reference floor display and print in layout? Preferably as dashed lines. when I send the plan view that shows the reference floor to layout it disappears. I am trying to show a basement level and the walls above so the architect will know where to add walls in the basement.

I have added a curved roof over an entry, see attached.I would like to curve out the front gable edge of the barrel, think of a baseball cap bill. I can't figure out how to do that???? Help.

Yes I did check winders and they still have segmented sides and handrail. Have also made sure it is tight to the wall

Javatom, yea am aware of cost, we are probably going to do it in steel and segmented with flat glass. Probably still expensive.

Wow, worked great. I scoured that DBX for a reference to curved can't believe I missed that. Thanks Will fill out signature

I have a curved stair tower and want to put a curved window in it, is there a way to curve a window in plan view? Not talking about arched tops Also is there a way to make the stairs curved to the wall and not have flat side segmented? curved stair.pdf

ok thanks, will try this.

When I use line drawing rendering it wants to keep rerendering. Is there a way to tell it not to do that?

I can help you with your project. I am in Franklin, NC and have drawn numerous projects in Highlands, Cashiers and Lake Glenville. Please contact me and we can discuss. scdrafting1@gmail.com

I looked at it closer and realized i have multiple eave levels on this piece of roof and that this mystery boxed eave was in the same position as another eave. I went back and made this piece of the roof plane its own piece and it went away. I had tried closing the program and reopening and it was still there. thanks for the comments.

Every now and then when doing boxed eaves I end up with an extra piece of boxed eave in the wrong place. Attached is an image of the problem and the plan. Suggestions? boxed eave1.plan.zip

the walls were aligned but i went through and got rid of the misc attic walls and it fixed the issue i had in several places. thanks.

thanks

Attached is a section with an arrow pointing at a line I would like to go away, also attached is a section showing the line, the floors are aligned. Is there a layer I can turn off that will make these lines go away in elevation view? And no I can't post the plan the owner is insisting on privacy.

Great. Thank you.

plan attached hugo master bath plan.plan.zip

I am missing a small piece of ceiling above the glass shower wall, I have pulled this wall down so there is an air gap, but even when the glass wall meets the ceiling I end up with a piece of unfinished ceiling the thickness of a 4" wall. What gives, can I fix this other than adding a polyline solid to cover up the missing ceiling??? THANKS

Drawzilla, Thanks for pointing that out. Sorry I can't post the plan, owners request for confidentiality. Thanks for your coments.

Must not have said the right curse words, that didn't work. However i selected the top wall and pulled its bottom up to the upper line and that made both lines disapear.

See attached image. In center of image there are lines at the ceiling and floor line. how can I make those go away. I have tried to find the layer they are on with no success. I have turned off the layer ROOMS and that eliminated some of these extra lines.

How can I create floor truss that looks like the attached. I have tried modifying the standard and I get what I want, but when I copy and paste it reverts to the standard profile. I am mainly interested in having a truss with the top cord to sit on the plate vs. the whole truce sitting on a plate. Thanks in advance for all your great help.

Eric, thats what I did to get the pattern vertical to begin with. However when I apply it it will some times be vertical and some times not. and then if I color it it will sometimes switch directions.