wkenddad

I would think that there was better text editing. Usually a text editor with a ruler which can include Tabs and Indents would be nice. I would like to have hanging indents to format some of my text. Example: M-1 Domestic clothes dryer moisture exhaust ducts shall terminate on the outside of the building and shall be equipped with a back-draft damper. Sheet metal screws or other fasteners that will obstruct the flow shall not be Unless otherwise permitted or required by the dryer manufacturer’s installation instructions and by the building official, domestic dryer moisture exhaust ducts shall not exceed a total combined horizontal and vertical length of 14 feet including two 90° elbows. Two feet shall be deducted for each 90° elbow in excess of two. 2022 CMC, Section 504.4. M-2 Make up air. When a closet is designed for the installation of a clothes dryer, a minimum opening of 100 square inches for makeup air shall be provided in the door or by other approved means. 2022 CMC, Section 504.4.1. M-3 Installation of a Listed Cooking Appliance or Microwave Oven above a Listed Cooking Appliance. The installation of a listed cooking appliance or microwave oven over a listed cooking appliance shall conform to the conditions of the upper appliance’s listing and the manufacturers’ installation instructions. 2022 CMC, Section 921.4 M-4 Domestic range vents. Ducts for domestic kitchen downdraft grill-range ventilation shall be installed as per 2022 CMC, Section 504.2. But would like it to look like this: M-1 Domestic clothes dryer moisture exhaust ducts shall terminate on the outside of the building and shall be equipped with a back-draft damper. Sheet metal screws or other fasteners that will obstruct the flow shall not be Unless otherwise permitted or required by the dryer manufacturer’s installation instructions and by the building official, domestic dryer moisture exhaust ducts shall not exceed a total combined horizontal and vertical length of 14 feet including two 90° elbows. Two feet shall be deducted for each 90° elbow in excess of two. 2022 CMC, Section 504.4. M-2 Make up air. When a closet is designed for the installation of a clothes dryer, a minimum opening of 100 square inches for makeup air shall be provided in the door or by other approved means. 2022 CMC, Section 504.4.1. M-3 Installation of a Listed Cooking Appliance or Microwave Oven above a Listed Cooking Appliance. The installation of a listed cooking appliance or microwave oven over a listed cooking appliance shall conform to the conditions of the upper appliance’s listing and the manufacturers’ installation instructions. 2022 CMC, Section 921.4 M-4 Domestic range vents. Ducts for domestic kitchen downdraft grill-range ventilation shall be installed as per 2022 CMC, Section 504.2. Also is it possible to add suffixes and prefixes to dimensions? For example a dimension of distance could have teh suffix of [12-'0" O.C.] where the O.C. is the suffix Am I missing something?

Here's the scenario: I'm designing a framed structure that will be constructed within a free standing metal building. The Framed structure wall exterior is separated from the Metal Building interior side of the wall by an air gap of 0" When I print the Framed Structure Floor Plan I would like to make the exterior metal building walls not display. This would also go for displaying the framing of ceiling and floor, etc. In Auto CAD you can set walls to different layers such as Wall-Ext or Wall-Int. Then you can turn off the layers you don't want displayed. How is this done in CA - I'm using version X10

I'd love to Could you please provide me with a little more direction

How do I create columns that have a stone base of one dimension and height with a post/column on top? Such as a 18" x 18" stone base 42" tall with a 8"x 8" wooden post from the top to the Truss above. Or even more fancy a tapered stone base with the wooden post on top? Similar to what's in the photo below

I can create a wall using the chain link item. But when I try to make a flat roof using chain link as the material it sits above top of the wall and has and OSB underlayment. How do I eliminate the gap between the top of the wall and bottom of the roof and also the OSB underlayment?

How would you add a gate? Is there a rounded cap for each pole?

Where can I find a symbol for these types of shutters? Used on the interior as a window treatment. Or how do I create them?