Charlenerene

THank you very just JMJ. I ended up building my another smaller room, raising floors and lowering ceilings to create the effect I wanted. LOL! That is much easier.

Hi, I am working on a box window and I want to make the windows themselves bigger. I also want get rid of some of the framing. Is this possible with a box window? Design to Shine Verson: X8 3.6 ghz quad core 16 gigs of ram Ninvida gtx 770

Thank you Scott, I appreciate the hand there. Rob, How do I use that file you have there? Do I just insert it somewhere into chief? Thank you everyone, appreciate the help.

Here is the plan. master_bath.plan

Hey Guys, So I am working on a wall niche. I made the wall and used the pass through window, removing the casing and sills. I then made the polyline solid and put it in the window. But I cannot get the polyline solid to show up in the camera view even after turning on every single layer. Any ideas? Best Regards, Charlene Design to Shine

This is a new ipad air, so it should work. It shows it connected, but won't transfer the data. The instructions to the Disto say to push the Bluetooth button to transfer, still no transfer. Other instructions say it should automatically transfer after measure.

So I finally got a Disto E7100i for measuring. I have watched the video with the room planner app and their measuring tool; but I can't figure out how they are getting the tool to load directly into the app. I thought it might be because I did not have the dimensions package so I bought that. Still even though it says the disto is linked via Bluetooth it is not sending the measurement information across. Any help guys? Is there some other module I need to buy for this to work? Thank you very much for your time. Charlene Design to Shine.

Thank you guys so much for the help I really appreciate it. To put into context the powder room is part of a much larger house. All I was hired to re-design was the powder room itself. At the time it didn't seem like a big deal, sloped roof how hard could that be right? Right? Yeah 4 hours later, watched the tutorial video and roofs still was evading me. Thank you very much for the help. Rlackore....your irl suspicion is very close to the actual reason it is how it is. Once this project is done I am going to spend a few more hours building roofs, just to play with them. Again I very much appreciate the help guys. Charlene Design to Shine

A ha, you can't have it open in Chief if you want it to attach. Good to know. /sigh Starting out as one of those days. Charlene Design to Shine powder_room_roof.plan

Now for the attachment, maybe.

Hey Guys/Gals, Man roofs are tough to understand. Attached is where I am on my plan. The wall opposite the door is the one that is meant to be shorter. Every time I try to change the height it auto-resets to 97 5/8. I have no clue where that number comes from since that is not the size of either wall. My mind is blown on roofs. Thank you very much for your help, I really appreciate it. Charlene Design to Shine

Thanks guys I really appreciate the insight. Evergreen...I didn't attach a plan because there was nothing to see, other than a square room. Joey....I am about to embarrass myself. These folks just wanted to upgrade a powder room to a full bath, so that is all I drew. Doug....I have never played with roofs before, outside of adding a skylight. I will try to do this now. Thank you very much for the suggestion. Charlene Design to Shine

Hey Guys/Gals/anyone that can help, So I am working on a bathroom that has a new issue for me. The wall opposite the door is an exterior wall and it is shorter than the interior wall. So the ceiling comes out 16" flat from the interior wall and then slopes down to meet the exterior wall. The interior wall height is 88.5" tall and the short wall is 62.5" tall. Now I know I can lower one wall but that always seems to leave a gap into the skybox. I have attached pictures of the actual room. Any help would be greatly appreciated, thanks. Version: x6 Processor: 3.4 quad core RAM: 16 gigs Charlene Design to Shine

Gotcha, will upload now. Thanks Schlothauser_Lg_Bath.plan

Version: x6 Interior. Looking at the right sink here, can anyone tell me why it draws the one sink lower than the other. It is user error (most likely) or a program quirk? see attached pic. Thanks for the help.