BlairDrafting

For anyone still curious about this issue: it appears CA is placing the sub fascia too high up on the roof plane. The soffit height is determined by the sub fascia in the roof plane structure. By increasing the roof plane's sub fascia from 5.5" to 16" (a ridiculous amount) I've found a workaround. I'm still not satisfied with this non-solution but at least it hides the problem.

Thanks for looking into this Eric. I went through the same process and didn't get the result so I'm guessing I've made a mistake somewhere along the line. I'll review what you did and will try again. Do you know the reason the concrete layer in the wall assembly overlaps the wall above when it is on the main wall layer? I would prefer not to rebuild the foundation if I've got a basement and a bunch of work into it.

I did. It didn't make a difference.

I wish the solution was that simple. Here's a picture of the parging layer set to the exterior layers section of the wall assembly. The parge layer still goes right up to the roof, but now it completely covers the main floor wall.

Has anyone seen this before? I've made a block foundation below a typical framed + brick wall. I like to show a layer of concrete on the exterior of the brick to show parging, but the parge layer overlays the wall above. It seems like this is a bug in the software, but I wanted to reach out to the community for some info before I submit to Chief Support. D-23-106 - PEARSON - JULY 2023.plan

Thanks Tundra_dweller. I hadn't thought of that.

I've recently noticed Chief Architect automatically will add numbering bullets to a text box when the first characters are a number followed by a period or parenthesis. For example: the text in my text box should be as follows ROOF LOADING: 0.72 KPa (15 PSF) - D E A D L O A D 1.89 KPa (39 PSF) - SPECIFIED SNOW LOAD 2.70 KPa (56 PSF) - GROUND SNOW LOAD but it looks like this ROOF LOADING: 0.72 KPa (15 PSF) - D E A D L O A D 89 KPa (39 PSF) - SPECIFIED SNOW LOAD 70 KPa (56 PSF) - GROUND SNOW LOAD Is there a way to have CA not automatically assume I want it to start numbering my lines?

You're correct. I must've confused the roof structure here with that of another job I'm working on. Thanks for pointing that out. I'm inclined to agree. Even in a situation where the roof requires a 14" (or bigger) joist I would still need to raise the roof to accommodate an appropriate heel height, which would likely also correct the soffit height. I would still like to know why Chief places the soffit above the bottom of the fascia in this situation.

Thanks for looking into it all. It seems like reducing the roof framing also reduces how much the soffit protrudes when this issue occurs. I would be interested to hear if anyone else has seen this happen to their roof planes.

Please see attached plan file for reference. I've drawn a revision cloud around the soffit area I've been having difficulties with. Since my previous post I've adjusted the roof structure material to 9 1/4" (down from 14"), which has mitigated the problem, but not eliminated it. There is a railing wall which defines the roof bearing for that plane. I'm curious why this issue would affect one roof plane and not the rest of them in the same area. D-22-119 - BROLLY - FIELDCREST - DEC 2022 (AS-BUILT).plan

I'm having an issue with soffits appearing above the roof planes. This mostly occurs with porch or deck roofs, but can also happen to a roof over dwelling. It is most noticeable on roofs sloped at 4/12 or less. I've been seeing this happen since I started working with Chief in X12 and thought I'd reach out to see if anyone else has thought of a solution. Renderings attached show above and below the roof plane.

My situation is similar in a broad sense. I've been working from an external drive with multiple plan files linked to one layout, some of which are linked from a different computer. The layouts I've been given to work with are often messy and are usually from previous versions of CA. I can see how X14 might have difficulty with reading from multiple sources and different CA versions.

Thanks Dermot. Next time it happens I will submit the report to the technical team.

Hi all, I've been working on X14 for a few months, and I've noticed a bug I can't seem to fix or find a work-around. When working in a layout file the plan file will sometimes delink from all the layout's viewports when I use the undo button. It usually only takes a few minutes to relink all the viewports to the plan file, but recently this happened, and it corrupted the plan file to the point it was unusable. I've never seen this happen in X13 so I'm wondering if it has something to do with the way X14 manages linked viewports. Has anyone else had this issue, and do you know a way to fix it? Thanks,

Thanks for the responses. Fortunately, this issue won't have a major effect on my drawings. As Solver mentioned, probably best to just move the labels.