BrentJohnJohn

Members
  • Posts

    45
  • Joined

  • Last visited

Everything posted by BrentJohnJohn

  1. Greetings, This has got me baffled. I am using a Backdrop that I uploaded (see attached Sky Backdrop I downloaded from the Web). However, when I run a Walkthrough, the Backdrop is not even close (see attached PBR Backdrop). I've also attached the settings page.
  2. Greetings, Is it possible to create a 3d Solid out of a PDF. I'm needing to insert custom text into the plan for a Walkthrough.
  3. Sorry. See attached. Verdexium_Test 03_23_25.mp4
  4. Greetings, I created a Walkthrough (see attached) and the video is very jerky. I've spent most of the morning searching the forum for a solution, but could not find anything. Your assistance will be greatly appreciated. Also, the video took over 16 hours. Verdexium 03_23_25.wmv
  5. Thank you so much for your assistance!!! I will look into this.
  6. Greetings. I am designing an office building and the client may want to have a Robotics Center included. Does anyone know of a recourse that I may get 3d Models of Robotic Machines to insert for the 3D Walk-Through?
  7. Greetings, I finally figured out the issue: I had a short wall on a unchecked layer that was causing the problem.
  8. Greetings, I have been trying to figure this out for the past 2 hours and am not having any luck. For some reason, the foundation is not aligning correctly. However, the wall is one continuous wall – red line. Any help will be greatly appreciated.
  9. TeaTime, I changed the wall type and then re-entered the wall type and all works now.
  10. Greetings, I have worked on this for over 3 hours and cannot find a resolution. My issue is the window exterior trim is covered by a Pony Wall exterior stone (36" height off floor). How do I remove the stone as to not cover the trim? Also, I did create a Sill, but as you can see, the stone is protruding through.
  11. HyperTrex, That is what I needed. I changed the Minimum Alcove and it works perfect. Thanks again!!
  12. All, Thank you all for your responses. I have changed the PDF to a PNG for ease of viewing. I'm wanting to create a Hip Roof Line over the Porch area.
  13. Greetings, It has been awhile since my last post. I have reviewed the Forum for more than an hour and not able to find any suggestions to my problem. Per the attached, I am needing to create a "roof" over the front entrance area. I have tried several different ways, and no success. Forney 01_09_23.pdf Forney 01_09_23 Sample.plan
  14. Greetings, It is possible to have the sizes in the Door Schedule to be feet and inches. They are currently in inches.
  15. Greetings, I've set my 2nd floor dimensions per the attached. However, when I produce the Auto Story Pole Dimensions (per attached), they do not align with the set floor dimensions.
  16. That worked perfectly - thank you much! I'm still using X13.
  17. Greetings, I made an adjustment to the second floor exterior wall by reducing the length of the stone walls. However, I tired adjusting the Attic Exterior Wall as well, but it will not allow. When I try dragging the "yellow" portion to align with the "yellow" wall from the 2nd floor, it keeps going back to it's original position.
  18. Eric, Sorry for the late response. Your suggestion work - clicked on the "Through Wall at Start" and "End" under Structure in Wall Specification.
  19. Greetings, This has got my confused. Why do the 1st floor exterior walls end finish show correctly. Yet the 2nd floor ends do not. I'm having this issue on other exterior walls, including 1st floors as well.
  20. rgardner, Thank you for the advise!
  21. Greetings, In creating a non-standard U-Shaped stair layout, a "gap" is shown from the 2nd floor. I am needing to fill this "gap' between the 2nd floor and the top tread of a stair case - see attached.
  22. Greetings, I am trying to create an arched opening in a wall, with sharp/clean transitions.